Build Daily

Latest

October 11, 2016 23:17

How to make a fence of mesh netting - new methods of calculation installation +

Light inexpensive fences mesh widely used to secure suburban areas.Set the fence of mesh netting can be anyone with a minimum of hand tools.Subject to the mounting technology and the choice of high quality materials, this fence will last 15-20 years.Before starting work, you need to study the types and characteristics of the grid, as well as to study in detail the instructions to avoid mistakes.

How to make a fence of mesh netting

How to make a fence of mesh netting

Types of netting

Article Contents

  • 1 Types of netting
  • 2 Types of wire netting
  • 3 Installing fence posts
    • 3.1 Step 1: install corner posts
    • 3.2 Step 2. Marking
    • 3.3 Video - A new way to install supporting pillars
    • 3.4 Step 3. Installing intermediate supports
    • 3.5 Step 4. Welding hooks
    • 3.6 Video - netting fence with their hands
  • 4 Installation tension fence
    • 4.1 Step 1. Mounting grid
    • 4.2 Step 2. Fixation fabric from sagging
    • 4.3 Step3. The final stage
    • 4.4 Video - Connection netting in a roll
  • 5 Installation sectional fence
    • 5.1 step 1 frame Making
    • 5.2 step 2. Preparation racks
    • 5.3 Step 3. Mounting sections
    • 5.4 Video - How to make a fence of mesh netting
Types of netting

Types of netting

The grid is made of black and galvanized wire netting so the quality is different.A grid of black wire is the cheapest and the most short-lived.It is covered with rust after the first rain or fog, and after 3-4 years comes into complete disrepair.Extend the life of non-galvanized netting can use paint or liquid rubber, which should be applied to the net to install it, and then periodically update the protective layer.

Netting from a simple black wire

netting from a simple black wire

mesh of galvanized wire corrosion is not afraid, and therefore lasts longer.It costs a bit more expensive than black, but absolutely does not need a protective treatment.Fences made of galvanized netting look neat and attractive.

Mesh netting galvanized

Rabitz galvanized

becoming more popular plasticised netting.This metal mesh covered with a dense layer of corrosion-resistant polymer, thus has high resistance to weathering.In addition, the colored polymer mesh looks very attractive and aesthetically pleasing.Although such netting is quite expensive, the demand for it is growing.

Rabitz coated

Rabitz coated

addition to quality, chain-link fencing different mesh size, wire thickness and the height of the roll.Cells can have dimensions of 10 to 65 mm, wire diameter 5.1 mm.Roll height of 0.8 to 2 meters, but most in demand -. 1.5 m length standard mesh on a roll of 10 m, custom made rolls at 20 m The smaller the cell, the more expensive the cost of the grid, because it increases the consumption of material..

Grid View netting Wire diameter, mm grid Width Live Mesh-section,% Estimated weight of 1m2 grids kg
mesh woven with rhombic cell 1,20 1000 55,0 4,52
woven mesh with the rhombic cell 1,20 1000 61,0 33,73
mesh woven withrhombic cell 1,20 1000 69,8 2,78
woven mesh with the rhombic cell 1,40 1000 65,5 3,8
woven mesh with rhombic or square cell 1,20 1000,1500 75,3 (78,9) 2,20 (1,94)
woven mesh with rhombic or square cell 1,40 1000,1500 71,5 (76,2) 3,00 (2,57)
woven mesh with rhombic or square cell 1,40 1000,1500 76,3 (77,0) 3,24 (2,74)
woven mesh with rhombic or square cell 1,60 1000,1500 73,3 (77,0) 3,24 (2,74)
woven mesh with rhombic or square cell 1,80 1000,1500 76,0 (78,9) 3,25 (2,75)
woven mesh with rhombic or square cell 1,60 1000,1500 77,5 (80,9) 2,57 (2,17)
mesh nettingfences 1,4 1000-2000 83,6 1,77
woven mesh fencing 1,4 1000-2000 87,0 1,33
woven mesh fencing 1,6 1000-2000 85,7 1,74
woven mesh fencing 1,6 1000-2000 88,0 1,39
woven mesh fencing 1,8 1000-2000 87,0 1,76
woven mesh fencing 1,8 1000-2000 89 1,46
woven mesh fencing 2,0 1000-2000 87,9 1,81
woven mesh for fencing 1,8 1000-2000 91 1,1
woven mesh fencing 2,0 1000-2000 90,7 1,36
woven mesh for fencing 2,0 1000-2000 91,7 1,23
woven mesh fencing 2,5 1000-2000 90,7 1,70
woven mesh fencing 3,0 1000-2000 89 2,44
woven mesh fencing 2,5 1000-2000 92 1,41
woven mesh fencing 3,0 1000-2000 92 1,74
woven mesh fencing 2,5 1000-2000 94 1,10
woven mesh fencing 3,0 1000-2000 93 1,53

Types of mesh fences

Tensioner fence Rabitz

Tensioner fence Rabitz

Fence of mesh netting is sectioned and tension.A first embodiment provides for the manufacture of rectangular metal sections inside which the grid is fixed.For sections use metal corners, profile and round pipes of small diameter.Connect them by welding or bolts, if not welding machine.Such a fence looks more aesthetically pleasing and attractive metal frame does not sag grid.

Sectional fence of mesh netting

Sectional fences from Rabitz

Tensioner fence installed faster and easier;Its design consists of the supporting pillars and the grid itself.Krepjat net with steel wires, straps, or hang on hooks welded to the poles.For the poles fit pipes of different diameters, concrete columns, wooden beams.

Installing fence posts

Installing the support pillar

Installation support pillar

And sectioned, and the tension of the fence marking, preparation and installation of poles produced by the same technology, so only in the first case, the pillars have to be stronger.This is an additional burden on the metal sections;If the support is too thin, fence necessarily skewed.

To work required:

  • roulette;
  • wooden pegs;
  • coil of thin rope;
  • building level;
  • hand-drill;
  • gravel and sand;
  • concrete solution;
  • scrap;
  • shaped pipes 60x40 mm;
  • Bulgarian;
  • primer.

Step 1: Install corner posts

allotted under the fence section is cleaned of vegetation, if you want to align, determine the location of the extreme poles.Experienced builders recommend the corner posts do more of the pipe cross-section than the intermediate, and dig in their deeper.For example, if the intermediate supports taking the profile tube 40x40 mm, then the angle is better to take 60x40 mm and 15-20 cm long.

attempting to install pillars:

  • pipe is cleaned of scale and oil stains, soil, spread out to dry;
  • with a hand drill to make holes in the ground a depth of 1.5 m;

    Drilling

    Drilling

  • poured on the bottom layer of sand, well tamped;
  • inserted into the hole shaped tubes;
  • put them on a level and reinforce bars or bricks;
  • fill the space in the holes with gravel mixed with soil to a depth of 2/3, ram;

    Filling the hole with gravel

    Filling the hole with gravel

  • fill the remaining space with concrete solution;

    Concreting of support

    Concreting supports

  • again check the vertical pillars, dub if necessary.

When the solution hardens a bit, you can remove the brace and start marking at the intermediate rack.

Step 2. Marking

between the corner supports tightly pull the rope at a height of 15 cm from the ground - it will be a fence line.The line should be divided into equal parts, corresponding to the width of the span.The optimal span the width of the netting to the fence is equal to 2-2.5 m;if it increase, net necessarily slack.Stand back from the far post in the desired position and drive a peg in the ground, and so on to the opposite corner.All pegs must be in contact with the taut rope and to be equidistant from each other.

Video - A new way to install supporting pillars

Step 3. Installing intermediate supports

Installing intermediate posts

Installing intermediate posts

In place of pegs are drilled holes for poles and covered with sand bottom.The better to control the height of the supports, the upper edge of the corner posts pull another rope.Now, insert the pipe into the hole, dub height and vertical, pour gravel and soil and tamped firmly scrap.On top of the concrete is poured and leveled surface.

concreting

Concreting

If you plan on mounting tension of the fence, and the soil in the area is sufficiently dense, intermediate supports can just put in the ground and concrete.For this purpose holes are drilled in half the required depth, and the pipe is inserted to clog hammer.In order to protect the columns from the upper edge deformation taking larger piece of pipe it is welded to one side of a steel plate, and put on top of a column.After plugging holes legs fall asleep with gravel and sand, sheds water for better sealing and a good ram.

Installing intermediate posts

Installing intermediate posts

Metal poles for the fence

Metal poles for the fence

Step 4. Welding hooks

Check the evenness of the pillars

Checking pillars evenness

About a week later, when the concrete is sufficiently hardened, you can continue with the installation.Fix the net on poles can be wire or clips, but it is more convenient to fasten it on the hooks.On sale are shaped tubes already welded hooks, but if there is a welding machine, cheaper to produce them yourself.To this end, suitable pieces of steel rod, screws, nails, even thick wire - everything that can be welded to the pipe and bend.In the column height of 2 meters is enough to make 3 of the hook: at a distance of 15 cm from the ground at 10 cm from the top of the pipe and in the middle.

Video - netting fence with their hands

Installation tension fence

Setting the tension of the fence

Installation tension fence

Step 1. Mounting grid

roll of netting put around the corner post, unwound a bit and put oncell hooks.To securely fix the mesh edge, you need to take a section of the valve diameter of 8 mm and a length of 1.5 m and thread the it into the first row of the cell.After that, put to a valve pipe and welded.Now pulling roll mesh will not sag.Secure the end of the grid, the roll is transferred to the next support by pushing it unwinding.

How to strengthen the grid

How to strengthen the grid

departing from the junction with the netting tube of 10-15 cm, the cells again threaded steel rod.At this time, it is not necessary to weld, it will simply pull the grid evenly.When the grid is put on the hook, the rod is removed, the roll is unwound for another flight again vdevayut fittings and so on until the end of the fence.To connect the two wires of the cloths used extreme vertical row of one of the rolls.

Tensioning device enclosure

tensioning device fences

Step 2. Fixation fabric from sagging

Even well-spanned canvas eventually droops slightly, so during installation you need to take care of additional fixation netting between the pillars.You will need wire cross section of 6 mm and a welding machine.The wire is threaded in the second or third row of cells horizontally along the entire fence.In areas adjoining the grid to the posts, welded wire.Then, in the same way the bottom edge reinforcing mesh, and at the end hooks are bent.Now the fence fabric is securely fixed on the supports and will not sag and sag.

How to install the fence of mesh netting

How to install the fence of mesh netting

Step 3: The final stage

When the fence is installed, you must perform the finishing touches:

  • put on top of the plastic pipe plugs;
  • paint the bars;
  • upper netting antennae twist 2 pairs coil and bend down.

The installation of the tension of the fence is completed.

Stages of construction of the fence of mesh netting

Stages of construction of the fence of mesh netting

Video - Connection netting in a roll

Installation sectional fence

Mesh netting as a work of art

Mesh netting as a work of art

Step 1 frame Making

scheme of installation of the fence

corner of 40x50 mm rectangular frame boil.Frame width 15 cm less than the width of the span length of 10 cm less than the height of the aboveground part of the column.Mesh size grinder cut section cut in the same cross section and the armature 8 mm.At the edge of a threaded fitting netting cell and it is welded to the inner side sections.After that frame sanded, wipe the dust, soil.

Production sections

sections Manufacturing

Instead angled wooden frame came down may be used

wooden slug

can be used instead of corner frame Step 2: Prepare racks

of sheet steel cut rectangular plate 20X5 cm and a thickness of 4-5 mm.Take one plate, applied perpendicular to the pole at a height of 20 cm from the ground and welded.The second plate is welded at the top, stepping back from the edge 15-20 cm. Similarly, attach the plate to the other supports.

Step 3. Mounting sections

Sectional fence Rabitz

Sectional fences from Rabitz

first section put between the posts, lift and put on a level.Then the sides are welded to the plate and go to the next span.It is important to align the section height to the upper crossbar of the frame were a single line.Once all sections of the weld area is cleaned, primed and painted the frame of the fence.

How to paint Rabitz

How to paint Rabitz

Embroidery on the fence of mesh netting ,

Embroidery on the fence of mesh netting-

Video - How to make a fence of mesh netting