Build Daily

Latest

August 12, 2017 18:06

A fence made of netting with his own hands

wire mesh is ideal material for light barriers.It does not obscure the light, and therefore is widely used for fencing of beds, gardens, designate boundaries of neighboring parcels.To put netting fence with his hands, you do not need to be an experienced master, simply by installing the technology available and to choose the right materials.

A fence made of netting with his own hands

fence netting with his hands

materials fence

Article Contents

  • 1 materials fence
  • 2 How to calculate the amount of materials
  • 3 Manufacturing tension fence
    • 3.1 Step 1. Layout area
    • 3.2 Step 2. Preparation of pits for pillars
    • 3.3 Step 3. Installation of bearing pillars
    • 3.4 Step 4. Mounting-mesh netting
  • 4 Manufacturing sectional fence
    • 4.1 Step 1: Assemble the frame
    • 4.2 Step 2: Prepare the grid
    • 4.3 Step 3. Installation section
    • 4.4 Video - netting fence with their hands

appearance, durability and cost fence netting depends on the quality of the grid.Metal mesh is available in three versions:

  • neozinced;
  • galvanized;
  • plasticized.

netting from a simple black wire the cheapest of all.It is not suitable for permanent fences because begins to rust after the first rain.Typically, untreated black mesh is no more than 3-4 years.To extend the life, non-galvanized netting should be covered with either paint or special structures, which after application form a water-repellent coating on the grid.Periodically, such treatment should be repeated that the result is more expensive than purchasing a galvanized mesh.

Netting from a simple black wire

netting from a simple black wire

galvanized netting not afraid of moisture and does not require protective treatment.She looks much more attractive, especially looks good so net sectional fences.The cost of galvanized mesh higher than the usual black, but because it is longer, and it is not necessary to paint every 2-3 years, this option is more practical.

galvanized netting

galvanized netting

plasticized mesh has a special polymer coating that resists corrosion.The coating is not only durable, but also a variety of colors, so you can pick the grid to match the main fence, or roof of the house.The most popular is considered netting blue and green color, sometimes you can see the white, red or yellow chain-link fence.

Plastified mesh

plasticized mesh

Compare mesh netting TM Kazachka other

mesh netting TM Kazachka Compare with other

Special attention should be paid to the support poles fences.Mesh netting can be attached to metal pipes, steel sections, concrete posts and even the wooden racks.

most convenient and practical supports are metal square tube.Manufacturers offer pipes already welded on hooks, specifically for the installation of fences made of mesh.To reduce the cost of fence installation, also use pipes b / y, and is welded hooks themselves.Furthermore, fastening hooks is not the only option, the mesh can be fixed to a steel wire.

Metal poles for mesh netting

Metal poles for mesh netting

How to calculate the amount of materials

most popular for making fences considered mesh-netting width of 1.5 m and a mesh size of 40-50 mm.Standard mesh roll has a length of 10 m. To the grid did not sag, supporting columns should be set in increments of 2-2.5 m. This means that one need not roll more than 5 bars.The above-ground part of the legs should be 10 cm greater than the width of the grid columns and dig in the ground should be 1/3 of their height.

So, if you want to install the fence netting 30 m long and 1.5 m high, to work need 3 rolls mesh and 16 bars in length 2.3-2.5 m on each column must be fixed 3 hook -. Top, bottomand in the middle.Multiplying the number of poles 3, find out how much you will need a hook.If the fence is sectioned additionally calculated amount of metal parts for the frame.The height of each section of the grid is equal to the width and length of the run is 2-2.5 m. The most convenient area for frame 40x40 mm to 5 mm thick.

A fence of corrugated board

We decided to build a fence of mesh netting?

Recommended necessarily familiar with other species fences.For example, read about the construction of a metal fence, a fence made of polycarbonate, an excellent tool fence of mesh netting to secure the fence made of brick.

Also read about the construction of a wooden fence!

Manufacturing tension fence

A fence made of mesh netting

fence of mesh netting

tensioner fence of chain-link fencing is faster than sectional, and cheaper.The installation process includes the markup, preparing holes for posts, poles and installation of fabric fence.

To work needed:

  • -mesh netting;
  • metal pipes of 60-80 mm in diameter;
  • metal hooks;
  • hand-drill;
  • level and tape measure;
  • corrosion primer;
  • paint;
  • Bulgarian;
  • welding machine;
  • concrete solution;
  • rubble;
  • sand.

    How to fix the mesh - netting

    How to fix-chain-link fencing

Step 1. Layout area

Take the wooden pegs and a long twine and proceed to markup.To begin to determine the location of the extreme poles.In these places drive in pegs, pull the string between them at a height of 10 cm above the ground.If the fence line has breaks, each of them also pose tracker and fixed rope.Further along the line marking is necessary to drive the pegs where there will be intermediate supports.The distance between the pegs have to be the same width and correspond to run.

Step 2. Preparation of pits for pillars

Drilling holes for pillars

drilling holes for pillars

In places marked with pegs, using a garden drill makes holes with depths ranging from 80 to 120 cm. The denser the soilthe less depth.The diameter of the hole should be slightly larger than the diameter of pillars.At the bottom of each pit arrange a sandy base 10 cm thick

Step 3. Installation of bearing pillars

Mounting supporting pillars

Installation bearing pillars

Make a fence of mesh netting

Make a fence of mesh netting

Prepare the pipe:. Clean their surfaces from oil stainsand rust, sanded, welded hooks.Welded seams trimmed, remove the scale, and then the tube is primed and painted.After that dipped into the bars of the pit, put them on a level, reinforcing struts.If all supports have the same height and are positioned strictly on the same line, it is possible to pour concrete mortar.During casting solution pierced steel rod several times to remove air bubbles from the concrete.

Mounting pillars fence netting

Mounting pillars fence netting

sometimes metal supports are not set, and hammered into the earth: make a small hole depth of approximately 30-40 cm, immersed in their pipes and clog them with a sledgehammer to the desired depth.In order not to break the upper edge on poles dressed scrap steel tube brewed with bottom.This method saves materials and dense rocky soils is justified, but if the soil is sandy and unstable, the support can lead to side.Link to article about the concreting of the pillars for the fence.

Step 4. Mounting-mesh netting

Installation of grid fences

installation of grid fences

To fix the net on poles, roll unwinding is not necessary.He raised vertically, put to the first support and catchy hooks.If there are no hooks, mesh bolted steel wire in three or four places.Between the surface of the earth and the bottom of the net is recommended to leave 10-15 cm. It is possible to fix and close to the ground, but then the cells quickly entangle the grass, under the fence will accumulate debris, branches, fallen leaves.

schemes

mount fixed the netting in the first column, moving to second.The roll is unwound at 2-2.5 m, put to support and pull the net.To tension was uniform, at the height of the roll in the cell threaded steel rod 1.5m Perform this process with the best assistant:. One person pulls the grid, the other fastens it with wire or catchy hooks.

Even taut netting sags over time, especially at the top.Avoid this helps reinforcing wire or long steel rods, threaded into the fence on the perimeter of the cell at a distance of 5-7 cm from the top and welded to the poles.Sometimes the wire is threaded, and the top and the bottom edge, departing from the ground of 20 cm. At the end of the wire ends and hooks are folded inward on all support posts wear caps.

Fences made of mesh netting ,

Fences made of mesh netting-

Manufacturing sectional fence

A fence made of mesh netting

fence of mesh netting

Layout and installation of support posts for section of the fence is made on the technology described above.The only difference is that the bars do not have to be a hook, and with welded metal plates.These plates are dimensioned 15H5 cm and a thickness of 5 mm;welded them on top and bottom of the rack, stepping back from the edge by 20 cm

Installation of the fence of mesh netting

Installation of mesh netting fence

To assemble the sections required:

  • -mesh netting;.
  • steel corners 40x40 mm;
  • Bulgarian;
  • roulette;
  • welding machine;
  • reinforcement bars.

Step 1: Assembling the frame

Measure the distance between the bearing bars and take away from him 15-20 cm - this will be the width of the frame corners.The height of the section is equal to the mesh width or height of the column minus 20 cm. Steel corners are cut to size sections and welded into a rectangle.Then the scale is removed, the inner and outer surface of the carcass is ground.

A fence made of mesh netting

fence of mesh netting

Step 2: Prepare the grid

roll netting laid on the ground, unwound 2-2.5 m and neatly trimmed grinder width.Now, in the extreme rows of cells on each side of the reinforcing bars are threaded.Between themselves, the bars do not need to be connected.

Step 3. Installation section

grid is laid on top of the frame and welded fittings to the inside of the corner.Further well pull down the grid rod and welded to the bottom, then fasten the sides.The finished section is raised vertically to posts and welded to the metal plate.It is possible to fix the section and bolts, drilling a proper diameter hole in the projecting part of the plate.

When installing the next section, you must ensure that the edges of adjacent skeletons are on the same line.Even a difference of 1-2 cm will be visible and give the fence a sloppy appearance.At the end of the section primed and painted.So you can without too much trouble to make a fence all sizes.

Fences made of netting functionality is not inferior to wood or metal

Fences made of netting functionality is not inferior to a wooden or metal

A fence made of welded sections

fence made of welded sections

Sectional fence mesh

sectional wire netting

Video - fence netting with his hands