Build Daily

Latest

September 05, 2016 23:00

Once again on the plasterboard wall covering

Plasterboard is an excellent finishing material, the indispensable alignment or construction of partitions, walls, ceilings.
The article provides technology plasterboard wall cladding described techniques cladding sheets of drywall.
read the article, you can own, without the help of professionals to sheathe the walls of plasterboard panel with your hands.

for plasterboard wall cladding is used for a long time.For example, in Russia, plasterboard has been widely used since the 50s of the last century.However, in the XX century produced material does not possess such high properties that make it available not only in cost, but also is suitable.

Plasterboard has several advantages compared to other finishing materials:
- high fire resistance and sound insulation;
- low cost;
- light weight;
- operability, practicality and simplicity.

What you should know in order to properly apply the plasterboard walls with paneling?

Consider highlights plating technology plasterboard panel walls.
for plating use different ways of fastening material, frameless and frame.

to constantly heated space recommended for drywall thickness not less than 12 mm The summer house for wall advisable to use moisture-resistant, fire-resistant gypsum board.

Frameless method of cladding with his hands based on the use of gypsum boards at least 12 mm thick.
This method is better to use on a flat surface on which the old plaster is well kept.In addition the wall must be securely mounted.
installation steps are divided into preparation, installation, finishing.
the preparatory phase is removed from the surface of old paint, wallpaper, plaster, dust and dirt.
render over damaged areas, cracks are sealed.For qualitative embedding surface, cracks must be at blurring carve a depth of at least 5 mm.Checking the surface roughness.
If irregularities are not more than 4 mm plasterboard sheets are fastened with a plaster or mortar or putty.
When the surface roughness of up to 20 mm sheets are stacked with an adhesive applied to the sheet by lines with a pitch of 25 ... 35 mm.If
irregularities up to 40 mm, the produced gypsum boards laying in two layers.The first layer is performed
sheets, cut into strips the width of 10 cm. The second layer is mounted from a single sheet and secured filler.
of the tools needed for the job you can not do without roulette, sharp knife, level, jigsaw, hammer rubber.
will be needed plaster, grout, paint and adhesive tapes mesh.
for fixing plasterboard sheets is recommended to use special adhesives.

Frame mounting method GCR
installation frame is required for high irregularities of the walls and on wood surfaces.
Skeleton way to wall cladding sheets of drywall provides installation frame designed for surfacing and fixing plasterboard sheets.

Instruments
Widget from SocialMart

frames can be assembled from a wooden beam or galvanized metal profile.

For the construction of the wooden frame is recommended to use a beam cross section of at least 30 × 30 mm, carefully treated with antifungal, fire compositions.Of the compounds can be recommended fluid Aquatex, Senezh, Drevoteks.When assembling the frame of timber is required to leave the top and bottom clearance for air circulation.
bars are fastened to the wall using dowels, nails.Under the sticks fit self-adhesive backing.
furring advisable to use wooden buildings.This will get absolutely clean room.

is expedient to use as scaffolds constructions mounted of galvanized metal such as a CD or UD profiles.
CD profiles are designed to perform the role of the carrier, and the type of UD profiles are guides.
With UD profile given the flatness of the surface and the type of CD profiles allow you to create three-dimensional designs and creates rigidity construction.
for wall plasterboard with their hands must perform a series of mandatory works.
preparatory phase involves cleaning the wall of dust, dirt, old paint and wallpaper.
On the wall is applied to the markup using a spirit level.
inflicted on line mounted bracket profile with screws or dowels.
The first step is to fix the extreme vertical guides.Slipping between the outer guide thread, paint cord or fishing line secured the remaining rails, while maintaining the flatness of the surface.
attaching the carriers are ready to install the reinforcing frame profiles.We must remember that the reinforcing and leveling profiles provide the basis to which is attached and gypsum board.
to stiffen the structure should be used U-shaped brackets.Incidentally, the U-shaped bracket should be fastened on the middle of the road marking.
collecting frame, constantly aware of the flatness of the surface.

Vertical supporting rails are attached through a distance of 400 ... 600 mm.Their length is equal to the height of the wall.

Sheets of drywall are attached to the frame with screws strictly at right angles.The cap screw must be recessed 1 mm.Step screws fastening sheet is 25 cm.
Primarily sheets mounted on the wall without openings.