Build Daily

Building Materials

August 12, 2017 18:07

The bonded plastic panels : how to understand ?

click fraud protection

The glue pvc panel: the walls

requirements Naturally, not every coating is possible to apply the adhesive and not everyone is able to stick another element.PVC panels are fixed according to certain laws, for non-compliance of which can pay your money and precious time.

  1. flatness.It should not be any distortions and irregularities, in addition, holes or drops no more than 4-5 mm.In case of excess plastic is simply not glued, or be broken.
  2. surface condition.The well-known fact that for oily and dusty plane is difficult to glue something.So, you have to clean and wash whitewash panel and the dust, get rid of the fat household cleaning products.

To glue the panels on the tile adhesive

How to glue PVC mosaics and choose

glue The most appropriate option for gluing PVC is mounting glue "Moment", which is designed for technical and decorative gluing parts.

Mounting adhesive

By using this glue is applied pistol technique that allows to put its dot.

Besides there are still adhesives: liquid nails, foam and tile adhesive (cement).They are all easy to fulfill their direct function, but each of them is perfect.

Speaking of thermo-adhesives, it is worth remembering about the abilities of the plastic to expand, which can lead to delays sheet.Such manifest his trick with the time when a constant thermal exposure sheet will simply not take place where expanded, but instead fall off at all.
Using liquid nails for the panel sheets

Liquid nails such situations do not cause, well, it is best to use non-expandable sealant, which is sold in every hardware store.It is flexible and heat-resistant.Professionals use only his.

How to glue pvc panel video

Wall design using plastic adhesive - popular at the moment is a repair of the walls.In the video you can learn how to choose the panel and as they are often mounted.

How to glue pvc panel: specificity laying on glue

As with any other kind of finishing, plastic lining process begins with the preparation of the coating.First, it needs to be cleaned and primed, but before you proceed to the primer, you should do some more action.

  1. angles.Often, in such rooms, like a bathroom or toilet, the corners are rounded, so that they become geometrically smooth dub their punch.If you do not, each of the wall display the plastic will be very difficult to you, which means that it will also affect the uniformity of the surface.With the powerful hair dryer plastic sheet can be bent, but if such an opportunity will not be?

    When forming the inside of the corners can be cut, to bend, but a 90-degree angle will look much better than 60 or 120.

  2. Finished panel corners

  3. Harvesting starter strip.This is not done, if you are planning to install baseboard and ceiling mount become plastic.But it is necessary in order to make a neat connection to the flooring panel.
  4. Installation Startup Panel

  5. And then proceed to the panels by PVC.It needs to be trimmed in accordance with the desired length and dwell space, then remove dust cloth.After the glue is applied.His, by the way, can also be applied in different ways.If the room is a good wall, the adhesive is applied along the perimeter of the strip and in the middle, as if the walls, to put it mildly, rough, adhesive dot mark.By doing all that, as it is written in the recommendations, you can be assured, the panels are glued to the wall well.
  6. panel with glue putting a wall.But there are some features of adhesion for each adhesive:
    • Liquid Nails.They should be left for 5 minutes to "cool down", so that they could harden to the extent in which they are securely grappled with the wall.Liquid Nails is best glued sheets.
    • sealant.Constantly need to press against the wall until such time as it ceases to fall behind.

Mounting corners conventional sheets

Tip: do not have to buy the factory compound and try to tie them.It suffices to use conventional plastic corners that are easy to glue or silicone sealant.Choose for the angular width of these inserts can be in the range of 20 to 50 mm.

Luck repairs!

instagram viewer