Cork insulation as a way to plunge into silence

cork insulation, the whole truth on this

No matter what manufacturers soundproofing materials, there is no universal tool for a complete cut-off of all existing noise in your home.The only way to be in utter silence - move into a deep basement, and there you can find a vibrating noise from the train passing nearby.Cork insulation can only partially solve the problem of incessant hum, wafting from the street and talking in raised voices from neighbors, their slightly muted.The fact that this material is sufficiently thin compacts of fine crumbs cork with a porous structure, through which the material has excellent cushioning properties.For the most part fine saves from cork impact nature sounds , and to a greater extent of your neighbors.

As an example, let's take a neighbor from the bottom, which is extremely loud voice.You have decided to close it on a shield of cork flooring and beds of this miraculous material, which, according to the promises of vendors, reduces any noise at 20 decibels.However, the voice of a neighbor you will hear almost as well, though in a somewhat subdued version.But your neighbor completely cease to hear your step, and even resolutely you jump rope, will not feel any discomfort at the bottom of the stamping, except that the chandelier rattled.That is exactly your steps will be drowned out by 20 decibels.But what, then, is good cork, and why to use it, you ask.It's all in the way of using the material.The thin sound-absorbing cork wallpaper - it is a myth.

Noise plug, or how much you are willing to increase the thickness of the walls

Thirty millimeters cork on zvukizolyatsionnym properties correspond to 150 millimeters or concrete 10 centimeters of pine timber.In this case you usually guaranteed for noise reduction of 20-50 decibels.As it turns out, on the basis of the foregoing, the mythical properties of cork, it's all - just advertising tricks?What about decibels is likely, but about the correspondences between the materials is really so.But remember, there are well protected by a wall of noise in the panel house, where just in the concrete slabs are used as material.Neighbors heard perfectly, but if the walls were three times thicker, but with a layer of insulation, then silence, no doubt, would have prevailed in each apartment.And stopper insulation when used arranged in a single layer panel made from this material (thickness of less than 10.5 millimeters), the effect is negligible.But increase the thickness of the insulation, put on top of an additional layer of insulation and decorative panels, such as siding on the walls and laminate flooring, and you will immediately feel the result.

only powerless against what home insulation cork tree - it is structurally sound, or, in other words, the vibration.

However, the most effective way to your room sound insulation will cover absolutely all surfaces of the stopper.It is, of course, is not about the furniture, which certainly would have been the original design decision, and on the walls, and the ceiling field.At the same time, we are considering putting the plate material should follow the example of brick masonry, that is, the bed one layer of insulation panels of the next layer stack so that the point of connection of the lower corners of the four panels accounted for the top center of one.In principle, the tight junctions of the effect will appear after the second insulation layer.If we give the third layer, again offset stacking plates with respect to the previous series, you can expect that not only the drums, but also air noise will hardly be heard.Over the cork can lay any cover, but it is better to leave it as it is, it is warm, very nice softening steps and extremely durable.

cork insulation, its installation and care

to lay on the walls and floor cork tree, a lot of work is required.As flooring tube can be laid in two ways, depending on what you purchased plate.There are those who are connected by a universal "tongue and groove".They can plank on concrete or hardwood floor of your home, as long as the surface is completely flat.The emergence of the mold material is not exposed, but still better to err on the occurrence of condensation on the underside of the plates and put them under the polyethylene.Top as an additional safeguard against the ingress of moisture put a substrate made of polypropylene 3 centimeters thick and begin to collect mosaic of cork slabs.We spread a row, followed by a second, which should be lifted and put to the edge of the first 30-degree angle, trying to hit the spikes on the slots.Lightly press while lowering the number of plates, and has been smooth, and most importantly, a strong connection is ready.Also, put the rest of the plate.Each subsequent row is placed in relation to the previous offset in polplity (principle of masonry).

To lay the plug on the floor and walls, and the ceiling with the help of glue, you need to quickly grasp the glue, the best rubber to make just enough to cover the surface of the sheet for full adhesion.Laminating room principle the same as that in the case of a floating or pazogrebnevyh coating that is offset by polplity. Stack cork sheets to be tight, without gaps, promazyvaya glue joints including .Thanks to the quick-drying glue chosen and grasped instantly, insulation of the ceiling is not more complicated than the installation of the plug on the wall.When you have finished, you can leave the cork in its natural form, or, if we are talking about finishing bathroom, toilet or kitchen, cover them with a special lacquer sealant.Apply a protective layer should be soft finely roller, and the need to comply with all rules of fire safety, fire hazard because of evaporation varnish.Upon completion of work necessary to ventilate the room for 24 hours, complete hardening of the sealant takes place after 8-14 days.Then the surface can be easily cleaned with a damp cloth.If the protective layer is disturbed, may be recoated without previous flatting.