Build Daily

Doors

August 12, 2017 18:08

Doors set just knowing all the tricks Installer

click fraud protection

Content

  • 1 Box loops independently
    • 1.1 Working with a router on the tie loops
    • 1.2 Preparation box and the right washed down loops
    • 1.3 washed down loops on the box
    • 1.4 box lock and mounting height handles
    • 1.5 Putting box
  • 2 Step by step video guide and subtleties tie locks
  • 3 Step by step photo instructions sidebar locks

So it's time to install the door, normallythis press is better to make after the wet work.Since the door and the box draw moisture and expand, that after installation they begin to strike sharply, and then when the humidity drops, gaps may become more and you can not guess the very Doors humidity if they are on the site.

IMPORTANT!If you decide to install a door at the end of finishing work, you need to clearly Gaugeable aperture size and vertical walls, to avoid distortions to the casing wall.

When you have decided on the size and fittings, it is time to determine where the future will be to open the door.When the door is much better to mount them according to the plan of the apartment.Now we define the floor, that is, if you already have coverage flooring, laminate or other coating.By then it just can calculate the gap between the floor and the door, if not then you can calculate the gap with tile or laminate plus solution plus the substrate, the gap under the door do depending on, of whether or not the mat usually make payment of 15 ml.

Box loops independently

determines where the door opens, look easy to open it.Put to one side the door, ideally for the convenience of work to produce the angular stops for door to door held its own, it will greatly facilitate the work.Retreat at 20 cm from the edge of the door put a pencil mark, putting a noose and put labels.Take, fasten screws hinge to the door, look to loop a well-kept.Take a knife and carefully building and with little effort encircle circuit hinge, as shown in the photo, and then with great effort conducting contour of the door hinges, perform the same operation with the second loop.As a result, we get a clear outline slaughtered.

loops Box can produce a chisel on their own eyes.You can of course more quickly with a hand mill.I do not think that this is the router that is large and industrial, it is a perfectly acceptable tool which need at least a couple of diameters for different types of locks.Fraser will greatly facilitate and accelerate the process of tapping the door hinge with the help of it you can accurately guess the depth of the frame, and it is very helpful if caught knots and irregular fiber wood.

Working with tie on a router loops

main thing when working to be very careful, because the rotation of the collet over 30,000 rpm and therefore it should be well fastened and naturally comply with safety regulations.

Warning note that there is a contact of the frame and lock the router with the surface of the door.And there is vibration, and if no action is taken, it is possible to damage the door leaf.To avoid damage to the door leaf should be used on the surface of the sliding materials for the frame and stop, you can certainly make templates, but it already requires skill.

And so proceed to sample the door hinge, take, exhibit depth on the palm of the router to use this loop set its pressed state between the stop and adjust the height of the burial.Especially not affect what diameter collet can be used to tie and 12mm.- 18 mm.We expose the focus limiter on the edge of the fix, and proceed to the burial.Clearly holding the milling machine, and without going beyond the boundaries of loops.Remains of finalizing a chisel, as a result we get a clear seat and fastens the loop.

Preparation box and washed down the right loops

We look through the slats of the box in the presence of curvature.Depending on the various types of profile are washed down, it may be 45 degrees, but in this, the classic case profile selection.Stabbed straight angles din rail do 2018 mm (this is based on the gap from floor 10 mm or 15 mm and a gap between the door frame and the door about 2 mm).The best and quickest way to facilitate self-installation loops.To do this, we take the two clamps and twisting them to the door at the ends.Put the rail, the box on the top of the clamp via gon Measure out 3 mm or use a loop to determine the gap.

is important to leave a gap between the edge of the box and the door leaf of 1-2 mm.This is to ensure that the door is not rubbing or creaking in the process of closing and opening.

Since the depth of the box is different, there is a clear need to find the gap.Typically the gap makes the edge of the loop plus 2 mm.The clearance height and lateral distance fasten the box to the loop, check the closing of all the excellent draw out circuit loops with a knife and remove the rail.

Instruments
Widget from SocialMart

washed down loops on

box Take the via, a chisel make the selection.This can be a router that's because in the photo is the same manipulation, exhibiting zero mark plus the depth of the loop.To use the second definition contagion stick box, it will not accidentally bury a sample.Sample a router box door for convenience fix the clamp.After finalizing fetch a chisel.Here and now is ready to match our door hinges well.

Box lock and mounting height handles

usual standard installation of the lock handle from 900-100 mm depending on the door lock, and ease of use.Locks and latches are usually different thickness mock strap and can be as square as well as the U-shaped edges.Consider options for tapping door locks, but the principle they have one.Castle with rectangular edges fasten to the door facing the center, on the basis that the handle is 1 meter from the edge of the door.We trace the outline of the building with a knife, and we get a loop to tie using a chisel or a milling machine.The process Tie castle with semicircular edges, these locks are generally designed for installation using a router.

It's not necessary to greatly deepen the sample under a decorative lock plate, it is better to let a little favor.Take, fasten the lock to the door end face considering that the handle is in the middle of the door handle away from the floor 1 meter contour of the castle clearly draw out a pencil;Take the desired diameter cutters;We expose the depth of penetration;Expose emphasis milling machine.Now slowly begin first sample, taking the contour, most importantly do not go by the edges so as not to damage the door.Getting Started the second phase of the lock frame, we are measuring the width of the lock body, take the right diameter collet and begin sampling depth.Change to an elongated collet and select the full depth of the castle.

Very neat work, firmly hold the machine, because it can be nails, knots, screws.It is important to know that there is a vibration of a milling machine, and a cover of the door leaf can be damaged (especially the cheap models of machine tools).

Getting installing pens, mark pen pencil points and draw out the contour of the lock insert for drilling in wood use the feathers of the desired diameter.Be sure to drill holes on both sides of the door, so as not to tear a piece of cloth.

Putting box

Since long we have already decided (2018mm).The width of the view with the condition that it is necessary to make the gap between the door frame and 2 mm on each side.It is necessary to pay attention to the loop, what's the longitudinal gap.Everything considered, do gash width.When assembling the boxes are very convenient to use the angular clamp.We put all the parts on a flat surface and set clear corners and slopes.An important detail to the door is not rubbing can be slightly tilted to one side of the extension.You do not need it at the correct gaps.We connect the elements of the door frame, screws pre-drilled holes for them to box is not cracked.Box ready for installation.

To your attention a video installation of doors, a variety of mounting options, wizards tips installers doors and ways of tapping door hardware

Step by step video guide and subtleties tie locks

Instruction Wizard

Jobs Fraser

installation box

Errors by installing doors

Step by step photo instructions sidebar locks

instagram viewer