Build Daily

Out Of Town

August 12, 2017 18:06

Gazebo with barbecue own hands .The best guide for the construction of

click fraud protection

Article Contents:

  • 1 wooden gazebo with a barbecue with his hands
  • 2 brick gazebo with barbecue and barbecue
  • 3 homemade brick barbecue.Step by step instructions
  • 4 Brick barbecue at the cottage
  • 5 BBQ out of the barrel with his hands
  • 6 Designs gazebos with barbecue

Besedka3.1

wooden gazebo with a barbecue with his hands

and first we will look at an example where a gazebo is made of lumber and barbecue - made of bricks.Immediately important tip: Look for 6-meter timber and plank.So it will be much less waste.

first paragraph of erecting wooden gazebo with a barbecue with your hands - is the choice of location for development and configuration.We take into account several important points:

  • entrance to the house and the entrance to the gazebo should look at each other (which is easier to hold tableware).
  • reckon with rules of fire safety.The gazebo will grill with open fire, do not build it right next to the house.

defined the place by building sand envisage

circuit foundation.Our drawings gazebo with barbecue suggest that the gazebo is octagonal, and the foundation under it is in the form of a circle."Otchertit" circle, you can use the pipe fixed in the ground, and tied a rope to it.

In our case, the fertile soil layer had a thickness of about 20 cm. Was excellent clay soil behind him.Construction is relatively small, therefore chosen as the base concrete footings.Earth beneath them better select and replace it with a mixture of sand and gravel.So you can align the height.

material for bottom binding serves bar section 100x100 mm.Not to be mistaken with the corners cut, use a template out of cardboard.For a device cross beams 50x100 better to use the board.To make it possible to harness the reliability seal metal corners inside and out.Perfectly suited galvanized 105h105h90h2 mm by 135 and 90 degrees.Do not forget about waterproofing layer of roofing felt between the posts, bases, and strapping.

Besedka3.2

gazebo with a barbecue with his hands step by step photo

Paul in the gazebo made of 50x100 square-edged boards.Immediately Scrollsaw in the size of the required amount of material.The face of the board better planed a plane, and the inside - to process an antiseptic (preferably in several layers).Fasten the floor with screws and make sure once again check the sill using a level.Besedka3.3

cantrail more convenient to construct the bottom.So it will be more convenient to the regrowth of locks and lengths of rafters.As a material for the rafters and upper trim use the same edged boards 50x100.Besedka3.4

In our case, a gazebo with a barbecue from a tree with his hands has octagonal roof .Therefore rafters Castle will also be octagonal.We carry it from the timber 100x100.Note the placement of support beams underneath.To install the octagon had to be increased with the help of boards in the thickness of 1.5 cm. Besedka3.5

gazebo with a barbecue with his own hands.Photo

proceed to production rafters .Perform propyl triangle in the lower attachment point.We will use it as the lower castle.Besedka3.6

As the top bundle, truss also going down.It will be easier to fix minor bugs.Besedka3.7

Our drawings gazebo with a barbecue provide for the installation of ten supporting pillars .We make them out of 100x100 timber.The better to carry out their installation, saw off the ends at an angle of exactly 90 degrees.Fasten the base of the pillars in the corners of the gazebo using 105h105h90h2 mm galvanized steel.Check the design with the help of the level.In this case, the installation otkosin not needed.Besedka3.8

Gazebo with barbecue own hands.Photo instruction

now conduct the installation of roof system and the upper trim.For fixing, we need:

  • Corners 70h70h55h2 mm 135 degrees;
  • Corners 50h50h40h2 mm 90 degrees;
  • plates connecting 80h40h2 mm.Besedka3.ya

The roof is made of inch board width of 100 mm and 150 mm.Stela its close;starting from the bottom and go around to the highest point of the structure.For convenience, use markup cardboard template.With it easier to mark the cutting line.Every board is fastened with two screws on each side.So the roof will not deform over time.Besedka3.91 Besedka3.92

Do not forget about BBQ of bricks with their hands, which will be located in the gazebo.Digging a hole for the foundation barbecue depth of 40 cm. Besedka3.93

Formwork can be made of boards from the pallet.Besedka3.94

blanketed formwork roofing material .The most convenient way to do this is with the help of construction stapler.Besedka3.95

fit into the hole for the foundation reinforcement (bars of 10 mm Class A3) and reinforcing mesh (d = 4, 100x100 mm).The foundation pour a mixture of cement and sand in a ratio of 1 to 3. Ideal brand cement M 250. In our case, it took five sacks.Besedka3.96

You can then sew along the perimeter of the gazebo simulator logs 45h146 mm.This will not only make the building more attractive, but also add a frame stiffness.Besedka3.97

sills are made of planks 50x100 mm.To fix them, use the corners 50h50h40h2 mm.This part of the construction is not mandatory, but it will make an arbor more comfortable for guests.Besedka3.98

Grounds benches are made from 50x50 timber.Fasten them at an angle to the walls via corners 50h50h40h2 mm.This is the most durable and ergonomic design option.

material for manufacturing top of the benches is decking 28h121 mm.To increase the strength, all the benches are connected to the ends of the plates 80h40h2 mm.

For visual separation arbor into two functional zones mangalnye side decorate wooden lattice .For its manufacturing is well suited 15x20 mm beams.Besedka3.99 Besedka3.991 Besedka3.992

wooden gazebo with a barbecue with his own hands.Photo

In this work on the pavilion is about to end and you can proceed to the construction of the brick barbecue own hands.

The simpler the design, the easier it is to carry out its installation without any errors.Therefore it is better to use simple drawings of brick barbecue without the frills.For the construction of need:

  • full-bodied red brick (360 pieces);
  • Fireclay brick sand color (90 pcs);
  • Furnace mixture (175 kg);
  • refractory mixture (50 kg);
  • Hot Corner 40h40h4 mm (7 meters);
  • galvanized furnace umbrella.Besedka3.993 Besedka3.994 Besedka3.995 Besedka3.996 Besedka3.997 Besedka3.998 Besedka3.999 Besedka3.9991 Besedka3.9992

For proper and accurate masonry must perform a number of conditions.Firstly, the solution should not be too thick.After installing the bricks should be easily adjusted by hand.Secondly, the ideal seam has a thickness of 3 mm.To this must strive to design was the most durable.Be sure to abide by the same seam thickness over the entire structure.Third, you can not rush.Laying is conducted strictly on the level.In this step by step instructions of building a brazier brick in a wooden gazebo can be completed.The entire sequence of masonry is clearly seen in the photographs.

Besedka3.9993

brick BBQ in the gazebo.Photo

can only cover roof shingles (in the example used red tiles Shinglas) with nails and construction stapler, as well as an antiseptic to treat gazebo and varnish.Antiseptic applied in two layers.As varnish is well suited glossy Yachting.Besedka3.9994 Besedka3.9995

brick gazebo with barbecue and barbecue

Those who are in the shower more than a mason, a carpenter than we offer step by step instructions of building the gazebo with a barbecue made of bricks.Skip the search space and layout stages under construction.All this is described above.Immediately proceed to the case.


1

Building brick gazebo with barbecue.Step by step instructions

brick structure will weigh a lot, so this time foundation necessary to make a solid and reinforced.Once it is ready, perform masonry.2 3

rafter system can be manufactured in the same way as for a wooden pergola.

4 (1 )

first row is better to lay out to dry.

5

constructs drovnitsu .It will also be the basis for the barbecue and smoker.6

continue to spread the barbecue made of bricks with their hands.The next firebox and worktop.Optionally, you can arrange a niche dish.

7

Gazebo with barbecue own hands.Staged photo to

proved we need to set the plate .Here is an option with removable rings.

8

barbecue Base is ready.It's time to lay out the table top from firebrick .

I

In laying necessarily use refractory mixture .

10

next stage of building the gazebo with a barbecue made of bricks with their hands - an organization chimney and forming a channel for the smokehouse.

eleven

in our gazebo will Russian oven .Forming for her under.

12

Each row necessarily reinforced wire .

13

walls are put at the same time.Accuracy check the work using a level.

14

Finish furnace vault .

15

In this case, the rear wall of the furnace had to push.

16

work will require a lot of time, but progress will warm the soul.

17

continue the construction of the brick barbecue with his own hands.Install door smokehouse. Finish arches over the barbecue, cooking stove and oven.

18

Grouting is always possible to instruct the assistant.

19

Above the stove can be set grid of stainless steel.In the future, it will be good to dry the berries and mushrooms, or utensils.

20

How to sew up the roof we mentioned above.

21

Gazebo with barbecue and barbecue their own hands.Photo

In this step by step instructions of building a brick barbecue is coming to an end.Complex gazebo, barbecue ready for delivery.

22

water to wash summing rear pergola.In winter, it can be cut off.

23

Tube doing three-channel.So the thrust will be stable.

24

Do not forget to cover the entire clutch impregnated with water-repellent effect .

25

to dry construction will take about a week.In this building the gazebo with a barbecue made of bricks with their hands completed.

26

homemade brick barbecue.Step by step instructions

1

Barbecue own hands.Drawings

Building brick designs start with a device robust foundation.The size is chosen according to the size of the future of the barbecue.

2 3

at a selected location dig a pit.According to arrange the edges of the formwork (it can be done, for example, from the boards of the pallet).Fill the concrete and armiruem base.Required for complete solidification of 1-2 weeks.

4

Base ready and you can start to build the barbecue.

5

Preparation of drawings and plans - a useful thing.They will help to make an accurate estimate.Here is a sample list of required materials:

  • Refractory brick;
  • wire for reinforcement of masonry;
  • sand and cement;
  • Corners of galvanized metal;
  • mesh or reinforcing bars;
  • Lime.

6 7 8

Barbecue brick with his hands.Photo

For the preliminary calculations, lay the bricks as they have to lie in the design.It is now clear where they will be laying seams, and how many half and quarter bricks need.

I

material absorbs moisture very well.Therefore, under a brick is better to put waterproofing material .A pair of layers of roofing material is fine.

It's time to begin construction of the barbecue.

10

Cooking solution.To this mix of cement, sand and the slaked lime in a proportion of 1: 3: 0.25.On the resulting mixture will eventually spread in advance prepared a brick.

eleven

Masonry require accuracy, attention and patience.We follow the seams equaled the bricks in the level.

12

working technology requires placing rows in staggered.We focus on the first row, starting with the laying angle, gradually filling the space side.

13

Mangal will be exposed to high temperatures.Therefore, the second row is better to put with clay-fireclay mix.

14

To make the base under the broiler, you need to install the rods reinforcement between opposite walls.They installed the furnace base.For example, it can be a metal pan.

16 15

burning process requires a constant flow of oxygen.For this purpose, the furnace brickwork must leave some gaps without mortar.

17

remains to grille bars or projections (depending on the masonry barbecue) and select the countertop.

18 19 20

Brick barbecue at the cottage

Brick barbecue - perfect for a suburban area.This is a simple, convenient and reliable design, which looks quite presentable.

We offer detailed guidance that will help even a person inexperienced in construction to build a building in the shortest possible time.

1

The first stage - drawing up a detailed plan.We give only a rough diagram of the structure.You must take into account the peculiarities of their own oven, her appearance, decorative elements and more.

2

poryadovkoy brick barbecue.Photo

Do not forget about the niche for firewood and charcoal.We expect a place to grill at a height of 65-70 cm from the ground.Stove should be placed below 10 cm.

3

masonry bricks for barbecue.Photo

After working with a pencil and a ruler, you can move on to the practical part.As in the previous instructions begin with foundation.

4

Under barbecue fit the same foundation, as well as a BBQ.This monolithic reinforced base.Digs a pit for his depth of about half a meter.The bottom is covered with a layer of a mixture of gravel and crushed stone, water and ramming.

5

are installing rebar, forming the frame.All that's left to do is to formwork.Now we can move on to the Gulf of base concrete.

6

foundations will need up to two weeks to dry completely.A little patience and you can proceed to the construction of the brick barbecue.

7

Fireclay brick - perfect for laying furnace.He did not hit too hard on the pocket, but strong enough and tough to high temperatures.Pre harvests cement, construction sand and red clay.They are necessary to create a solution.Ahead of time pour the clay with water and hold it so a few days.

8

prepare a solution, you can proceed to the brickwork.Working slowly, according to plan, lay out row by row.Continuously monitor the clutch with the level.

I

first spread pedestal oven barbecue.It should not be too high (70 cm).

10

second row spread by moving the start tier to a half-brick.

instagram viewer