Preparation of concrete walls for wallpaper or how else to change their appearance ?

Finishing concrete walls - options for every taste

can transform concrete can be plaster, putty, paint, trim plasterboard, wood, plastic, cloth or wallpapering.Each method, which is carried out finishing concrete walls , in his own good, and, of course, is not only positive but also negative aspects that should be taken into account when planning repairs.

Plastering, along with a long service life, has a big disadvantage - is a dirty job, but how to plaster concrete walls, can understand each.Plasterboard, making the room sound and heat insulation with its fast timing of construction, reduces the size of the room requires accompanying works and is not suitable for hanging heavy objects.

Casing surfaces with wood paneling is a simple, hiding all the bumps, but a very expensive operation.Wallpapering - a very common type of wall coverings, even in spite of the fact that in their application remain on view everything, even the smallest irregularities.

As for painting walls, this method being very practical, and using non-toxic paints, safe, not suitable for new buildings, buildings, since even a slight drawdown their lead to cracking.

Plastering and painting concrete walls

Consider the correct version as plaster concrete wall.To begin the surface shall be marked serifs, about 30 pieces per 1 m2, depth up to 5 mm.Also, the wall must be free of dirt, dust, and small protrusions burls and abundantly wetted with water.Next, the thickness of the next layer via beacons.

If necessary, in case of large differences, it is necessary to use a metal mesh.Just the process of application, it is done in layers.The first layer is sprayed, is not too thick solution to 5 mm thick.The second layer, the primer is a base and produce dense mixture after complete solidification of spraying.

Next, the floating wall and wetting it with water for a week.It was after these operations can proceed to the application of the last layer, which is prepared and mix carefully to avoid major factions and heterogeneity.The resulting surface must be flat and smooth, without cracks and hillocks.

painting concrete walls also requires some of their training.First, the surface should be cleaned and primed nazhdachkoy special blends by hand or by mechanical means.This is followed by all the existing bumps flatten putty, using a wooden spatula.

After solidification of this layer is made sanding and re-coating.After completing all the preparatory operations, you are ready to paint.It is carried out by two thin layers with a brush, roller or spray gun, depending on the amount and the coated area inaccessible places.

Sheathing plasterboard bears in itself also functions such as leveling concrete walls and disguise their defects.This finishing method lies in the fixing of plasterboard sheets on the previously set frame or directly to the wall.The process should start with strengthening the guide, and then the profile itself.Drywall should be put, starting from the top and securing it with screws, with their caps must be recessed.With regard to the resulting joints are placed on the grid, and then a layer of putty.

Preparing concrete walls under the wallpaper and plastic

Pasting wallpaper the walls must be carried out on the prepared base.All cracks, notches and bumps should be sealed and applied primer for concrete walls.Next, the calculation of the required amount of wallpaper and trim, in accordance with the size of the room.Next, apply glue to the wall, and when you specify the conditions in the instructions and on the wallpaper too.

We should wait until the canvas is well saturated.The sheet is hung parallel to the wall, thus arranged its natural plummet, after which it is pressed against the wall and smoothed.Subsequent stripes are exposed on the resulting level.

To wall decoration fabrics need to have a certain level of skill.Primarily qualitatively be prepared surface.Methods how to align the concrete walls have been described above.

After that should be paid attention to the preparation of tissue, it is necessary to check for shrinkage by soaking and determining the change in size.If any, then everything is ironed linen.

crop width should be as large as possible to reduce the number of seams and a length slightly larger ceiling height.Thereafter, all cooked strips are sewn in the solid piece to each wall separately and unwound in roll adjustment.Fabric must be glued at the corners in the tensioned position, the adhesive-free web edges should be for mounting on the end of the process, after drying on the adhesive already attached to the wall tissue.

Decorating the walls with plastic does not imply a preliminary plastering concrete walls.Plating process is very simple and begins with the installation of wooden slats to the wall, the distance between them can be arbitrary.And then, they are fastened by a stapler plastic panels, one by one, starting from the corner.Surpluses can be cut with a hacksaw.