How to insulate garage doors with their hands correctly ?

What to look for at warming the garage door?

For the most complete understanding of what is necessary to insulate the garage door, it is advisable to remember the basics of physics and chemistry.Thus, fluctuations in day and night air temperatures lead to the formation of condensation in the garage, which is extremely negative impact on the state of the machine, and finishing the interior.In a short time on the metal surface can be formed corroding its corrosion deteriorates existing wiring on the walls and in the nooks formed mold, exposed to destruction even fabric upholstery in the car.

plaster used to finish tiles, wall paneling - all this crack, fall off and lose the aesthetic appearance.What can we say about those cases when under the influence of low temperature condensate freezes?In this room, you can easily lose not only the beloved "iron horse", but also undermine the health.Experts say that as a result of work on the insulation in the garage temperature should not fall below + 5˚C.

Getting insulation garage door, should take into account a number of nuances.Firstly, the significant role played by the right choice of the insulating material.The most common options for this type of insulation works - mineral wool, extruded polystyrene (styrofoam).However, it should be noted that the foam is quite flammable, but features excellent moisture resistance and low thermal conductivity.Mineral wool, on the contrary, is characterized by a good fire resistance, but the low rate of moisture resistance.

Do not forget to properly assess the work area to stock up on sufficient amount of insulation and related materials!

Secondly, you need to focus their attention not only to such a concept as "thermal conductivity" of the material used, but also the "thermal inertia".It reflects the rate of temperature change of a design over time.Thus, doing insulation garage door with his hands, should be guided by the fact that their thermal inertia outside to inside should be increased, and the thermal conductivity of the insulating material - decrease.That is, the surface of the garage doors and walls must be heated quickly, but slow to give it warmth.

How to insulate garage doors with the help of vinyl inserts and thresholds?

slots, often taking place after the gate installation, not only contribute to the penetration into the cold, but also "leak" of warm air.That is why the garage door insulation is necessary to prevent these processes.For this sealing is carried out through slits existing modern vinyl thresholds and insertions.They allow quite effectively retain heat inside the building, thus saving on energy costs, prevent penetration of dust inside the garage and not like rodents.

Installation of vinyl inserts to insulate the gate as simple as possible - they are attached to the edges of the gate.For greater convenience and better attachment to them has special notches, arranged longitudinally.

If the gate is covered with old peeling paint, it is best to remove it and the door cover new layer of coloring composition.As for the installation of vinyl threshold, here requires some preliminary work.So, clean the area around the gates of all the existing contamination and to assess the threshold condition.In some cases, you can get it aligned with special mixtures, however, if the protective threshold is quite old, it is easier to replace it with a new one.

recommended to arrange the foundation for it before laying vinyl insulation.For this purpose, usually used rubber or smooth wooden beam. After completion of all preparatory work can proceed directly to the installation of vinyl threshold, which is a continuous band of a certain width.Before installation, remove the vinyl seal garage door!

seal is placed along the garage threshold and trimmed the size of the gate.For the most efficient insulation is recommended to cut the tape with a small margin, that is, its length should be slightly larger than the threshold length.Provide high-quality vinyl gasket to mount the base can be prepared with a special glue or nails.Of course, nails contribute to a longer period of operation the material.

Warming shutters garage doors - how to make a right?

Warming gate leaves will require you some effort, cost and time.Firstly, it is worth remembering that the condensate is continuously formed between the metal surface of the door and the insulation material.Avoid this allows the corrosion protection of the gate with special formulations.Second, if you want to glue insulation directly to the gate leaf, ensure that that there is no air gap between them.

Third, if you prefer the installation of insulation on the crate (this option is recommended by most experts), do not forget priming its wooden elements.This will protect the structure from mold and deformation.It is mounted crate insulation sheets are attached with glue.Offered for sale can be easily found in the adhesive composition of the spray bottles.Externally, they resemble tanks with foam and provide a certain comfort in the work.

However, for installation of insulation you can use any adhesive, characterized in moisture resistance and ensures good adhesion between the selected materials and wood crates. After completing these works it is necessary to take care of protection of the insulation, which is masked by a more durable material, such as OSB (oriented strand board) or a thin board.Please note that the drywall for these purposes is not suitable, as it is quite heavy.