Build Daily

Utility And The Host. Room

August 12, 2017 18:07

How to make a shelf in the closet and get a roomy storage?

click fraud protection

plan how to make the shelf in the pantry

Utility Room is very comfortable when things are spread out on the shelves and set them under laryam, but upon entering the apartment, you often see only the bare walls.Of course, it is possible, not particularly trying to tie the corners of the wall normal board, only fit them into the right size, and will quite roomy shelves, but will the robust design, there is no certainty.

So let's think about how to make a shelf in the closet, and beautiful, and durable.For work, we need planed-edged boards, decorative laminated plank, plywood, carpenter's glue, a protractor, a special plane - sampler (or elektrorubanok), screws and finishing nails, as well as supplies for the boxes.

Among other things we need for the shelf brackets, and always made of metal, plastic, sooner or later let you down.By determining how shelves are installed - the letter P, the letter G or just along one of the walls (it all depends on the room size and shape), proceed to markup.The distance between the grocery shelves quite different than that which is necessary for folded items.

If you are going to put on the shelf with bottles marinades and compotes, you will need a strong board, about 30 millimeters thick, while for things to be enough centimeter. height of the lower tiers of product must be greater than the upper (usually put down all the dimensional and heavy), for all things compartment may be the same .

Getting forming racks

assume that the repair has been made, and the walls are lined (at this point we have the priority task is to supply the pantry and do not finish).With the help of level meters and make a mark where the brackets will be fixed at the rate that the racks are universal, equally suitable for products and things.The height of the shelves - 40 cm, and it is enough for the cylinders, and piles of laundry.

First, fasten the brackets to the wall opposite the door, at the rate of 50-60 cm between the supports.We put the board with a gap in the wall about 1 cm and fix them with screws or bolts, which hath a little hole at the top, in order to drown fasteners.Side shelves are fastened to the brackets and only the region that is adjacent to the face rack, install to the previously installed shelves from the bottom metal plates with holes for the screws.

lower front section 3 shelves do not on the whole length of the wall and divide this land vertically mounted sheets of plywood fastened to the corners of the lower tier of the continuous and to the floor, for 2 or 3 parts.Divide in half, if the height of a small storage area, while on the one hand to the plywood, and the other end fastened to the bracket shelves, leaving the second part to the boxes.Three compartments, one of which is a width of about 40 centimeters, and the other two - identical, do in the event that the top shelf at high altitude, then leave for a narrow branch of the small ladder.

produce and put in drawers

Make a box for clothes is not difficult, just need to take accurate measurements, to have enough space to install rails on the outer sidewall.But it will be the final stage, and for the beginning measure off the desired length of the boards, sawing and undertake the plane-sampler with which we do internal folds at the ends of the front, rear and side walls of our future designs.

The larger box, the thicker should be his wall and the bottom, and the stronger the need to take accessories.

depth rebates should correspond to half the thickness of the plates, as well as the width of the shelf.Now lubricates notch sides with glue and applied thereto, fixing finishing nails, first the front and then the rear wall, so that their butts lay on greased with glue seams. With gon reconcile shape of a box, so that all angles of 90 degrees correspond .When the composition hardens, carefully sandpaper grind joints.

now smeared with glue the bottom edges of the resulting frame is applied pre-cut to fit a piece of plywood with a verified form and nailed his finishing nails.It only remains to fasten the front panel bezel, which in the front wall of the drilled 4 holes for screws.At the very front panel drill holes for the handles.All collect (try to keep the screws from the inside is not passed through the trim), and the box is ready.It remains only to install hardware on its side wall and fasten the guide inside the battery compartment.

instagram viewer