Build Daily

Floor

August 12, 2017 18:05

3D self-leveling floors with their own hands

click fraud protection

Today's technology and interior trends allow to create real miracles.If you want the sofa in your living room standing by the sea or on a huge map of the hemispheres, and in the bathroom living dolphins, your wishes can be realized together with tankers 3d floors .

Content

  1. Advantages of 3D self-leveling floors
  2. How do 3d leveling floors?
    1. casting technology process to prepare the ground
    2. Priming basis
    3. base layer
    4. Putting drawings
    5. top finishing layer
    6. Protective lacquer layer
  3. Photo 3d self-leveling floors
  4. Video pouring 3d self-leveling floors

Advantages of 3D self-leveling floors

Modern three-dimensional flooring can add variety to the interior of your home, but in addition they have the following advantages :

  • environmental cleanliness;
  • ability to withstand enormous loads;
  • resistance to abrasion and impact;
  • dimensional floor much easier to clean than the tile, because has no seams, and embossed tiles often have problems with the "retention" of mud;
  • self-leveling floor is much warmer than the same tile, it is more pleasant and easier to warm up;
  • at the same time, in the summer you will not suffer from the heat, because the temperature of the coating is always comfortable.

How do 3d leveling floors?

Poured floors with 3d effect is achieved as follows:

    1. Preparing the base substrate to be coated image.
    2. then figure covered with a transparent finishing layer of plastic and lacquer.

As a result, you get a three-dimensional floor depth (width) picture which can be controlled by the thickness of the polymer applied.

Figure can be created using a motley multicolored images of wood, pebbles, flowers, sand, rocks, stones and other natural materials for self-leveling floor 3d.Given the huge variety of textures and colors, you can always find a decent option, which will complement the interior of your home.

casting technology to put the self-leveling floors using 3D stacking technology is similar to the usual self-leveling flooring.But it still adds a few steps and provide the floor 3D drawing .

main stages of placing self-leveling floor with 3d effect with his own hands:

  • preparation of the base substrate;
  • drawing of the image;
  • cover drawing self-leveling liquid polymer;
  • varnishing.

process to prepare the ground

self-leveling floor is installed over the concrete floor.In order to properly prepare the ground you need:

  1. Sand concrete base with a modern grinding machine with high-quality tips.
  2. Get rid of all defects (cracks, holes) with the use of mortar.It is best to use compositions based on cement or epoxy resin.
  3. thoroughly clean the surface from any debris and construction dust with a vacuum cleaner.
  4. Do not forget to degrease the surface.

Priming basis

After cleaning the concrete joints should be primed twice with a special material with deep penetration using a brush or spatula.The better you do the job, the more robust will be self-leveling floor screed.After priming is complete, leave the foundation for self-leveling floor to dry.It will take about a day.

base layer

polymer coating - the best option, as it has excellent characteristics, which allow the use of drawing, creating a 3D effect .

Laying the base polymer layer has a strict rule: flooded surface must be perfectly smooth, without the presence of air bubbles.This result is achieved by compliance with all the rules and regulations specified on the package.

Putting drawings

For pattern can be used two technologies: application of the finished image and create their own compositions.But in the second case, you will need to spend a considerable amount of money on paint and artist services.If you have the makings of an artist, you can draw a picture yourself.It will not only be beneficial to the economic side, but also exclusive.Remember that before applying the topcoat layer, the paint must be completely dry.

application has finished drawing is the most common method.To do this you will need to select the image you liked, on the need to edit it and print out the printing on vinyl or fabric banner.

On the base polymer layer, apply the image so that there are no air bubbles.

top finishing layer

mixture is poured evenly.To remove the bubble surface will need a spiked roller (15-20 minutes after application).

This stage of the work to be performed in special shoes with spikes as in the photo.

Once, for a few days, tighten the floor with plastic wrap.Complete drying time depends on the height of the polymer layer, as well as temperature and humidity.

protective layer of varnish

order to protect the floor from mechanical damage and adverse effects of external factors, after drying of the finishing layer it is covered with varnish.

To learn more about the installation of this type of flooring technology, you can view cognitive photos and videos , presented in our article.

Photo 3d self-leveling floors

Video 3d pouring self-leveling floors

instagram viewer