Plating Technology baths inside lining

sheathe bath inside lining - this is the best option for the interior decoration of this type of premises.

Molded perfectly fit the needs of a bath from a bar: it retains heat well, do not miss the steam and fits into the style of the room.

His most important plus lining is that you do not need to invite experts to sheathe the walls - you can do it yourself.

do the job properly with your hands will help you a video where reflect all stages of work.

choice of material and surface preparation

Before plating the walls, you need to decide from a treeyou want to see the interior trim.

It is best to use a profile lining made of hardwood, asconiferous trees will give off vapors are harmful to human health.

To trim paneling, you can select the following types of hardwood timber: lime, oak, alder or birch.

Lipa is of high quality heat retention, moisture resistance and ease of processing.

Molded oak will be the most robust, and alder - have a slightly bitter smell in the preparation of the bath.

Photo:

Birch cost you less likely, but it has a low resistance to moisture, so it can be used only if the roomdry enough.

bath If not planned too hot, we can turn our attention to the coniferous trees: pine, spruce, pine or larch.

Least resin will allocate cedar, moreover, this material is very beautiful and resistant to the processes of decay.

Molded spruce would be best to keep warm, and larch - have a maximum resistance to moisture.

Do not use pine battens for the pair, asit allocates a lot of pitches, but it is well suited for coating the walls of the room predbannom.

Once you have decided on the material, you can do lathing device on the wall.

Before that, you need to decide how you will cover the bath from a bar inside lining - you can do it horizontally, vertically or diagonally.

If desired, you can sheathe bath, combining horizontal and vertical cladding.The choice of direction depends on exactly how you need to have the crate on the walls.

steam rooms for baths from the beam is only suitable vertical type clapboard cladding, becauseIf the board to lay horizontally in the grooves will collect water.

Stela crate bunk perpendicular to future compliance with the steps in choosing a 50-60 cm batten boards, pay attention to their thickness -. It should exceed the warming layer lining.

If the walls are uneven, you need to close up from the inside, tucked down plywood or planks of wood.

If the roughness of the walls is too strong, it is possible to use suspensions profile systems made for drywall.They are fixed to the walls of the dowels, keeping step about 40 cm

To crate turned out even better to use at work building level -. It will help to make the location of the strips exactly vertical or horizontal.

Doing crate your own hands, you can save significantly by using neobstrugannye board or slab - because this material is still no one will see.

much more important to get the job done correctly, the lath has been a strong and reliable.

Warming and bath paneling

Before thinking how to sheathe clapboard bath, you need to take the structure of insulation to the heat retained within the walls.

It is best to insulate the walls of the bath timber suitable basalt wool - it is resistant to high temperatures and extremes, and has a composition of inorganic material that does not emit any harmful substances.

In her laying with his hands is no big deal, most importantly - observe basic safety precautions and not to touch the material with your bare hands, becausebasalt wool can cause severe skin irritation.

wool slabs should be laid in the gaps between rails crates to avoid cracks and gaps, asotherwise through them very quickly to leave the warmth, and you will not be able to make enough hot bath.

After laying the stone wool must be placed on top of her and vapor control layer - you can use vellum or thin polyethylene, cross-linked with each other for it.

Before you lay the material, make sure it is completely solid, otherwise it will not be able to perform its functions and quickly begins to miss the moisture.

right to lay a vapor barrier material should be in a horizontal direction, starting from the bottom, so that the sheets are placed overlapping.

When it is placed, it is necessary to glue tape sheets for better fixation.

Internal steam - a very important step, because it will not only protect the bath from the heat loss, but also keep intact the wiring, which could dampen, if not a vapor barrier.

Before bath clapboard sheathing, the material to survive for some time in the room to the board adapted to the microclimate of the bath.After a day or two after that, you can begin lining.

battens laid His hands very easily - she immediately go to bed without a gap.Lay the material can be in different ways, all four of them, each has its own pros and cons.

Application Method lining

Can be laid battens using klyaymera - metal clip that fits over the stud lining and then attached to the crate with a nail or screw.

This method is good because it will spoil the board can be quickly and easily replaced by a new one.

Best used for plating baths are protected from rust galvanized klyaymery, as is the case with screws and nails.

Stainless steel materials will protect the walls of your bath from brown stains that may arise from the use of unsuitable materials.

easiest to sheathe the walls lining the direct driving in of nails in the studs.In this case, battens directly to the sheathing nailed galvanized nails.

This method is suitable for all types of material, except in cases where the spike is too thin and fragile, becausein this case, the attachment points may appear chipped and cracked.

can sheathe the walls and the other in a similar way - an oblique driving in of nails in a spike.

However, in this case, there is a great risk of damage to the walls and ceiling, so if you're not a professional, with his own hands a bath paneling is better not to do.

durable and reliable method is through attachment, but it does have a significant negative - the location and mounting material will be very visible, which creates an unattractive appearance of the bath.

It will be possible to close up the hole with a wooden pin, but it will not last long due to strong temperature changes.

First start sheathing ceiling, fixing the first bar lining opposite the entrance.

best to use dobojnik for Welding of nails, becauselining thin enough, and hammer it will make uncomfortable.

Video:

After battens fixed on the ceiling, you can move on to the walls, leaving a distance of 3-4 cm for air circulation.

same gap must be left and trim lining the walls (between the wall and the material).

air to circulate freely under the material, on the need to secure the crate small strips.They are fixed perpendicular arrangement lining.

See the step by step how sheathed ceiling and wall paneling, you can on video - it will help you do the job by hand.

Video:

After lining installed, it should be treated.

For this fit wax or lacquer with special impregnation composition - it will help keep the battens from moisture and prolong its service life, as well as enhance the aesthetic properties of wood, asafter treatment will be easier to see wood pattern.

To protect the linings of the parasite, its coat with antiseptic - it is odorless and completely harmless to humans.