How to insulate the metal door with his own hands

With decreasing temperature, the pressing question becomes warming entrance doors, as heat losses can reach 30%.This affects not only the domestic discomfort in the room, but also on utility bills.In order to insulate the metal front door, you will need about two square meters of insulation and no more than one working day time.This is not a high cost, which quickly pay off.

Choosing insulating material

1. Mineralized wool
2. basalt slab
3. styrofoam or polystyrene
4. Jam

This is the standard insulating materials, which can be purchased in DIY stores.It does not rot and is inexpensive.However, as a heater, you can use any improvised filler capable of insulated metal door.This can be:

1. Pressed wood shavings or sawdust (Stipa)
2. old quilt or blanket
3. Vatinovy ​​material
4. Wooden edging bars

your doors, metal doors, insulated thus reliably prevent the escape of heat from the room.

Methods for warming a steel door

There are several options for insulation doors metal, the price of the materials on the chosen method does not depend on.Depending on the type of metal door and structural nuances, warming is performed from the inside, but from the outside of less.To learn how to insulate a metal door, look at an example using foam, but the installation rules for all kinds of the insulating filler - are the same.Visual benefits of this simple process on how to insulate the metal door with video instructions there at the end.

Fixing insulation to the frame on the inside

1. Standard sheet fiberboard, two foam sheets of 1x1 meter, silicone, self-tapping screws and spray foam plus a simple set of tools - is all that is required forwhat would your external metal doors were insulated.
2. cutting fiberboard sheet size doors.Drill, a jigsaw and a knife - cut holes for the eye, a keyhole and door knob.
3. foam cut out the size of immune cells defined stiffness ribs and tightly adhered to the back of the door leaf.It also does a necessary functional holes.
4. is important to note that any cracks and even reinforcing ribs give rise to thermal bridges.Eliminate vulnerabilities can using the foam.
5. thermally insulating filler should fit to fill all available space.Surplus and hillocks spoke cured foam is removed with a knife for drywall.
6. prepared fiberboard sheet is attached to the frame with screws.Mounting is done in increments of 10 - 15 cm along the perimeter and horizontal stiffeners.Work must be done from the top down.
7. Upon completion, the inner sheet fiberboard will be the basis for decorative door.

Warming metal door has a non-removable panel

1. task of warming the metal door panel has a non-removable hard but doable.Consider the option of warming a loose door heat insulator.Pay attention to the design of embedded lock.Such warming is possible only if the lock has a protective pocket and friable mixture will not be able to get into gear and will not lead to the blocking of crossbars.
2. Otherwise, the question is how to insulate the metal door, with the outer insulation is achieved storony.V Depending on your choice, you can on the outside of the perimeter of the door frame to sew from a wooden beam or metal "U" - shaped profile.
3. Insulation is attached in the same manner as described above.The front side, a metal entrance door is closed with a protective facade covering.Material must be chosen taking into account the location of doors.
4. If your front door is in the stairwell, you can do an ordinary fiberboard, but if a way out of the house leads directly to the street and exposed to precipitation, the material to choose more resistant to their negative influence.Plastic or galvanized metal, it is quite cope with this task.

Warming doorframe door

1. In order to keep the heat in the room, just a little to warm the front door.Leakage of heat, and can occur even in places dock door frame to the wall and just inside the door.
2. All visible cracks, plug hemp, wool or felt.Carefully Trumbo screwdriver or narrow spatula.Slightly moisten the surface puttied cement mortar or putties.
3. The wider the gap, the best blow with foam.Speaking cured foam is removed with a sharp knife and shpaklyuyut.
4. to seal the perimeter of the abutment web front door to the main box, there is a self-adhesive tape with a foam or rubber gasket.In the market of construction materials, it offers a wide range of similar products with different functional parameters and technological qualities.
5. door seal pasted correctly, creates a vacuum tube between the double doors at the entrance, or simply seal Insulated metal entrance door.