Build Daily

Plasterboard

August 12, 2017 18:08

Frameless mounting drywall to the wall

click fraud protection

Content

  • 1 Installation of drywall on a flat surface
    • 1.1 Methods for applying the adhesive
  • 2 Applying foam
  • 3 Bonding of gypsum board on the wall with disabilities planes

Often it occurs in many question whether it is possible to glue the drywall to the wall?And the answer is quite simple.Drywall - a tight three-layered material.It can be used for any type of room finishing.This depends on the type of material that can be highly resistant to humid environments and normal.

more relevant question is, what can be glued to the plasterboard wall?This can be done on the quick-and it is very viscous mixture.To this end, suitable compositions based on plaster from a reputable manufacturer Knauf.You can also use as a means of bonding assembly foam with a low coefficient of expansion.

How to glue the drywall to the wall?The issue is highly relevant where you want the speed and the need to preserve the space and the walls need to be aligned in any way.Especially because drywall is a modern versatile material that can be used not only to "drywall", but also perform complex transitions and interior elements.

Uniform application of adhesive

uniform glue

Before proceeding to the description of work processes, it is necessary to consider the available technologies and options that work:

  1. sticking with adhesive plaster Knauf on a flat surface;
  2. pasting sheets using the foam with a low coefficient of expansion;
  3. installation by adhesive to the walls with large deviations from a single plane.

Installation of drywall on a flat surface

consider a way to glue the drywall to the wall with minimal deviations which do not exceed 5 mm.In this case, just enough to cause the adhesive sheet and sticking it to the wall.But the technology is not as simple as it seems at first glance, because in finding sheet in its place will be difficult to align.In this connection, apply pre-marks on walls and ceiling, which will be the reference for aligning sheets in a single plane.

Thus, using rules or longer necessary to determine level of irregularities on the wall.With their help it turns out the most convex part, which will be the reference point.

From her indented 10 mm (thickness of the sheet), and with the help of the level mark applied on the floor and using a plumb line is duplicated on the ceiling.With both the benchmark sheets can be positioned on a wall with minimal deviations.

After applying all the labels pre-cut from the same plasterboard lining.On these sheets are installed with bonding.

But before you glue the drywall to the wall, you need to spend all communications.Low-voltage and low-voltage lines can be carried out directly under the sheets with their pre-fixing to the wall in increments of no more than 50 cm. The recesses for Escutcheon and boxes should be made in the wall in advance, because then it will be uncomfortable.High-voltage power lines need to invest in Stroebe and fireproof sleeve.

After all the preparatory work necessary to prime the surface of the sheet and the wall.In this case if there was a whitewash, it is necessary to remove it.Methods to remove the paint.

If you paint, the better option is to buy a soil mix with the name "Contact" or "Betonokontakt".Its price is quite high, but the glue on it will be held no less firmly than on the surface without paint.

The next stage begins sticking to the plasterboard wall.To do this, dilute the amount of gypsum glue Knauf, which will be sufficient for bonding one sheet.These measures are necessary in connection with the instant of its hardening.So as not to face the above problem, it is necessary to fulfill this condition.

Instruments
Widget from SocialMart
Methods for applying the adhesive

Methods for applying the adhesive

Methods for applying the adhesive

Depending on the degree of wall roughness depends on the method of its application:

  • If the wall has a small deviation,it must be applied in small portions at intervals of 25 cm along the edges of the sheet may be less in the middle.Also, the adhesive can be applied directly to the wall as desired master.
  • If the wall does not have significant deviations, the adhesive is applied with a notched trowel evenly across the entire sheet.

After application of the adhesive layer will look at how to paste the drywall on the wall.This should be done quickly and accurately.The first thing you need to install on the bottom edge of the backing sheet, and then aligning its position relative to the marks on the floor, pick it up and press it to the plane.Using rules defined level or long bulge in the sheet and tapping or pushing successfully removed.

If a level-usually, it is not recommended to tap on it, so it is enough to lean against the wall and mark the place where you want to tapped.Then, remove the side level and align the position, after - check the plane again.

After aligning the sheet it is necessary to back it with the help of a piece of wood or other devices for a few hours.

The backup sheet , glued with foam

backup sheet, glued with foam

Applying foam

One of materials for fixing plasterboard can be foam with a low coefficient of expansion.But in this case, the sheet must be secured more reliably, because the strength of the foam expansion will tend to push him away from the wall.If you miss the time, you will eventually turn out bumps, get rid of that is simply impossible.But before that, you must also be primed surface of the walls and slate.And the process of aligning its provisions is no different from the first embodiment.

important to carefully use foam, if you draw a soiled foam article as to clean the surface and hands.

Bonding plasterboard wall with disabilities planes

Mount drywall adhesive to the wall as possible, even if there are deviations of up to 4 cm. But in this case it is necessary to use guide 10 cm wide of the same material.They are glued to the ground, where there is a larger deviation.Then, by increasing offset amount of adhesive remaining on the wall swings.

Glue for drywall

Glue for drywall

wall processing technology and methods of leveling it in place is no different from the first and second method.Here it is important not only tapping too far from the indentation and which can lead to the formation of irregularities as a failure of the sheet.You must also be sure to use the marks on the ceiling and walls.This will avoid the trouble in the form of adjustments, or the remainder of a small dip, which is callous your eyes.

The glue drywall to the wall in this case?One of the great resources for this will be the glue "Perfliks".It has good adhesive properties which appear immediately after application to the surface.The sheets can be glued on gypsum plaster mixture, and a small thickness using the "Fugenvyuller".It is important to remember that the persistence of the solution is 20 minutes and the work must be done quickly.

instagram viewer