Instructions for the production of joiner's bench

When we instigate repair work or simply want to equip your home, often in front of us there are a number of challenges and obstacles.And if we approach this issue professionally, then it should start with the right equipment our workplace.And in order to most effectively perform all the necessary work on the house, should first take care of the joinery machine.

It is in your power to build carpenter saw personally, because it is, in addition to what will be a very useful thing, is also a valuable experience, so to say, advanced training in your farm.And if with the joiner machine you can handle, you doubt the success of his future endeavors sense it will not be.

So, we start to work.

What we need in the process of construction?

To begin with we define what joiner machine - is a certain kind of ordinary table created for the convenience of working with wood.The minimum height for such a machine - about 70 centimeters.

Of course, in the process, we need lumber.It is advisable to stock up on planed timber, pre-processed and manufactured in a single size (you need thicknesser).Thus, greatly facilitate the construction of the frame structure - a kind of base the entire machine, which should provide maximum strength.To fix the stiffness we need the wedge elements to be hammered into the holes on the side-bar screeds.This simple manipulations allow you to, if need be, to dismantle the structure very quickly.

should be noted that the main condition for any kind of machine is exactly the functionality that should be put forward in the first place with a handwritten manufacturing workbench.Behind it should be as comfortable and easy.

Next, we will describe all the stages of manufacturing process.

constructs Workbench

first stage.

All jumpers must be cut into the legs, then fix them with screws or glue.As we will cover the finished fabric has a size of 40 to 610 to 1,980 millimeters.Note the height of the installation by consulting with your growth.

To lower jumpers fix marking gauge.It presses the surface of the table clamp and cut it to the appropriate markers, using a saw with fine teeth.Where there is a groove, we performed several vertical levels.All the excess with a chisel remove.All necessary prodelyvat with each of the four legs.

Next, we need to collect himself workbench.

Each leg must be carefully fitted jumper.To fix these jumpers should use screws with a length of 6.5 centimeters.Start with the bottom, and upload to the top.There is an option and a simple construction, which does not need any slots and the bridge are directly attached to the legs by means of the same screws.In this case, they must stand for a few foot (approximately one more in thickness).

third stage.

Actually, the end frame structure is going in the same way (as can be seen in the image below).

fourth stage.

fix the side frames in a horizontal position and set the jumpers (the same method of use for attaching them).Each jumper is attached with three screws.

Next we clear the frame, making it so that all - and edges, and the top jumpers - on the same level.Then take two bars, whose length will be the length of the legs between our design, fastened one behind the other - to the cover.The lid should be placed so that the rear part acted beyond 1.2 centimeters.To fix the cover use the clamp.

fifth stage.

came all the clutches of attachment.Measure vise, remove the lid and is doing a corresponding hole jigsaw.The bars, which will be held in this place, also need to sawdust.Put the lid back on, fixing it with adhesive (can be used all the same notorious screws) and set a vice (for this you will need to do through holes in the lid and bars).Important: under the heads of screws is required to place the puck!

sixth stage.After

can install overhead jaws that are designed to work piece not be damaged during processing.They need to stick to the steel jaws.

Demountability

Also, it should be noted that not all cases, it makes sense to build a monolithic structure.Often, a person is simply not enough space, so even in the preparatory phase should determine whether to move the workbench, or it is set forever.If it is dismantled, it will take up much less space.

Video - circuit assembly workbench