How to make the ceiling hidden lighting - 10 useful tips

essence concealed ceiling lighting is that the light source (usually LED Strip), hidden in the eaves.All that is visible to man - dim lights along the contour of the room.This light is enough not only to illuminate rooms, but also to create an interior with a "twist".

Most often, this option is hidden illumination installed in the living room and bedroom, at least in the kitchen.This is due to the fact that the ceiling cornices are made of plasterboard, which service life is reduced significantly when exposed to moisture.

As you know in the bathroom and kitchen c humidity temperature a little higher, so here cardboard moldings seldom used.In this case it is better to install spotlights in the ceiling!

we now consider the types of covert illumination of the ceiling, as well as how to make such coverage with their own hands.

Typescornices

As we have said, the first thing you need to perform the installation of the cornice that hides and LED strip.Today decided to make the design of their plasterboard and polyurethane.And he and the other option looks quite attractive, the only difference is cost and strength properties.Consider the advantages and disadvantages of each of the eaves.

drywall constructions

Gypsum cornice flush ceiling lighting is a construction of the profiles (UD and CD) and gypsum, which are mounted and lamps.

Design Advantages:

• high strength;
• can be installed tape and spotlights;
• attractive appearance;
• niche under the ceiling is a heat-resistant;
• heavy fixtures can be attached to profiles.

Disadvantages:

• high cost structure installation;
• long setup time (minimum one day);
• need for specialist services.

On this basis, it must be concluded that, given time and enough money to make a hidden ceiling lighting for the cornice plasterboard is a right decision!

Polyurethane design

Cornices made of polyurethane are more popular when installing wiring in the house or apartment.This demand is justified by the obvious advantages of this type of niche.

Advantages:

• low price (the price band of 2 meters within 1,500 rubles);
• ease of installation works (design, you can easily make your own hands);
• small-time costs (hidden lighting ceiling can be done in a few hours).

Disadvantages:

• low strength (it is impossible to consolidate large lamps);
• less resistance to high temperatures.

The bottom line is that if you decide to connect the LED strip, the second option is more sensible because requires less time and money!

Installation backlight

With the advantages and disadvantages of each type of cornice we understand, now consider the methods of self-assembly concealed ceiling lighting.

Gypsum niche

First we need to prepare the following materials and tools:

• drill;
• elektrorubanok;
• screwdriver;
• hacksaw;
• construction Roulette;
• marker;
• «metal» Shears;
• screws;
• dowels and screws for fastening the profile;
• drywall;
• Profile (UD, CD);
• LED ribbon.

So, you first need to create a drawing of a niche for the installation of the ceiling hidden lighting.It can be closed and open (an example is shown in the picture).

Further, according to the project of the walls are marked by mounting profiles.To do this, use a marker and tape measure construction.

Then, using the screwdriver UD profile fixed to the wall on dowels.For these profiles can be mounted CD profile (every 50 cm).

When the frame of the profiles will be completely ready, you can install plasterboard.

Please note that the mounting plates should be joint to joint.All seams are sure to seal the special filler, and when it dries, prime with ready ledge and go to the installation of lighting fixtures.

It is best to carry out the installation of the ceiling hidden lighting LED tape, it just fits inside the eaves, along with the power supply.

Polyurethane niche

Installation polyurethane cornice long it will take much less.

First we need to prepare the following materials and tools for the installation of hidden lighting:

• building level;
• roulette;
• marker;
• ready cornices;
• adhesive agent (liquid nails or acrylic plaster);
• nylon collars.

first wall being prepared for operation: cleaned of wallpaper, shpaklyuyut, get off paint or new wallpaper.Next, you need to mark up the walls of the installation of the cornice.It is recommended otchertit parallel to the ceiling line, below 5-10 cm from the top, around the perimeter of the room.

Please note that if the walls and ceiling in the room uneven, then it is better not to use the building level, and the distance from the ceiling, it should be the same everywhere!

Then you can proceed to the installation of the cornice for indirect lighting.It is best to use liquid nails.Use Connect nagelnoe common matches (in the play areas are small holes in which connecting set match) to the joints neighboring cornices were more securely fastened.Such nageli necessarily be installed in corner joints products.When the niche is ready (the glue hardens), it fits into the LED ribbon, which can be additionally fixed by means of nylon straps.

Another important caveat - the power supply of the lamps must be taken outside the limits of the niche.This is due to the polyurethane main disadvantage - the inability to withstand high temperature.When the power pack is warm.

also like to note that the polyurethane cornice is often used when mounting tension ceiling hidden lighting.

Tips for installing

recommended to learn some useful tips that will help make the ceiling hidden lighting more correctly, and most importantly - safe:

1. method of wiring installation of fixtures - Vago terminals.No twists should not be.
2. Try to avoid joining aluminum and copper conductors.
3. If ceiling lighting scheme will be difficult, then to create it to obtain a separate group of wires from the main panel.
4. all wires inside the niche (if they are installed spotlights) protect the corrugated tube of self-extinguishing material.
5. When connecting the light switch on the break to go phase conductor, not a zero.
6. for mounting lighting using LED strip with one meter of length not more than 60 light-emitting diodes.Products from 120 to five lights are too bright and will not create a cozy atmosphere in the room.
7. Use lamps of the same brand and capacity.If the schema will include various items in the same line, the ceiling concealed lighting can have a different brightness and intensity at remote locations that will spoil the appearance of the room.
8. Do not run in the niche of the LED strip is longer than 5 meters in series.This will lead to the fact that at the point of its passage remains burnt trace.Long tape must be connected only in parallel.
9. polyurethane cornice must have a large area for bonding with the wall.Otherwise, it will disappear quickly.
10. cement the addition of a paper tape When docking gypsum boards.

That's all that I wanted to tell you about the installation of hidden lighting ceiling with his hands!If you have any questions on this topic, be sure to set them to our experts in the "Q & A" category!
Also read:

• floor illumination in
• apartment How to make lighting
• apartment How to make antenna for TV