How to connect the fridge - 15 useful tips

Option 1 - No additional communication

Inthis case refers to the simplest technique that only need to install and connect to the mains.

instructions on proper connection of the refrigerator with your hands consists of the following stages:

1. Check the cabinet and the power cord for defects and damage that may occur after transport.
2. Prepare a suitable place to be near a power outlet, so do not connect an extension cord.
3. Placing the body at a distance of 10-15 cm from each of the walls (for air circulation).
4. Twisted feet to the unit was in a strictly horizontal or vertical position (without distortions).
5. Check the level of correct installation work to the body standing straight.
6. Connect the cable to the network.

That's all the technology to connect a new refrigerator to the network with their own hands.As you can see, nothing complicated, and can cope with connecting even people who have not had anything to do with the installation of household appliances.

Option 2 - From the cold water connection

Ice Maker is used to create ice, which can later be added to the drink.There are self-leveling device and stationary type.

In the first case, the design has a special tank, which is filled with clean water and (manually).To connect with a stationary refrigerator icemaker, it is necessary to bring the cold water to the appropriate connector.

You can do it on their own in a short period of time.First you need to install the refrigerator on a prepared site.After that you need to "bump" in the cold water pipe house (or apartment).Depending on the type of tubes which are used for supplying water, purchased necessary materials: adapters stopcock coupling filter etc.After that, according to the diagram in the attached instructions must be connected to the body of the communication, as shown in the photo.

Useful tips

To Your equipment will last longer and thus effectively cool products, be sure to consider the following tips when you connect the refrigerator with their own hands:

1. sure to leave a gap between the wall and the unit casing.In its absence, it may be overheating, which would entail the failure of the technology (as the warm air will come back to the system).As we have said, the minimum distance from the wall should be 10 cm.
2. Pay attention to the fact that some products manufacturer provides special helpers that create the necessary clearance for the installation.Typically such variant structures represented elongated sidewalls.
3. Included with the icemaker can be a special water filter.It must be connected according to the instructions.If the kit is not provided for the filter, be sure to buy the appropriate option in the sanitary product (consultant will tell what it is necessary to buy).Himself connect household refrigerator through the filter is quite simple, you just need to fix the unit on the wall and connect the cold water to the icemaker.
4. To avoid overheating of the system, you need to install the housing away from radiators and other objects that radiate heat (for example, a gas stove).Also: Do ​​not set the refrigerator next to the oven and floor heating (on the boards laying film underfloor heating is a requirement to negotiate).
5. Before connecting the refrigerator directly to the network Check the wiring and sockets.If there are damaged, replace all the necessary elements for new ones.
6. wiring have to be earthed to carry out installation of equipment without grounding is prohibited.
7. If your network there are significant voltage drops, additionally install surge protective device (eg stabilizer), which will protect your appliances from premature failure.
8. Choose the installation location so that there is no need to connect an extension cord.Cord should be enough to be sure the outlet.Connecting the refrigerator through the portability is not recommended, becausevery often the extensions are of poor quality and melt even at low current loads.
9. If not put a refrigerator away from the oven, it is necessary to prevent heat transfer between the two products by means of a veneer.
10. little trick electricians - that the door closes easily, slightly unscrew the front legs, so the body will be slightly "swamped" back.
11. Set the refrigerator should be strictly on the level, so that in the future he will not noisy and buzzing at work.If you do not level, possible small bias, which is one of the main reasons that machinery noise.
12. When choosing a refrigerator, you are staying in the built housing, we recommend to install it in a cabinet in the kitchen.Such an idea can save a free area (if the kitchen is small) and at the same time will make the interior more attractive if you certainly do not choose a model with a designer casing.Also, built-in appliances (if the model is small and single-chamber), can be installed under the worktop in the kitchen of one of the sections.In this case, no one will guess where your food is kept.
13. If you decide to buy appliances with ice maker, be sure to connect the refrigerator to the water through the filter.Otherwise, the ice can be messy becausewater in the pipeline is not always suitable for drinking.
14. is not recommended to place equipment under the window, becausein the heat of the summer sun's rays will heat the building, which also negatively affects the efficiency of the device, as well as accommodation in the balcony.
15. After the first start or defrosting food spread inside the camera is recommended after 3-4 hours of operation of the equipment.

At the end of our advice, and now you know exactly how to connect the refrigerator to the water supply network, and with his own hands!We also recommend you view the video tutorials on visual self-assembly technique.

Also watch the video, which is more compact describes how to connect the refrigerator after purchase and home delivery:

Related items:

• Why noisy washing machine and how to fix it?
• How to choose a TV for
• Home Why fridge severe frosts