Build Daily

Bath, Shower

August 12, 2017 18:08

Repair their own hands cracks and chips on the acrylic bath

click fraud protection

Content

  • 1 Common types of acrylic baths damage
    • 1.1 Subtleties repair
    • 1.2 Tools Required
    • 1.3 Instruction for beginners
  • 2 make repairs fine scratches,burn-through
    • 2.1 Remove the rifts
    • 2.2 repair of chips in the bath
      • 2.2.1 FAQs users

Acrylic tubs have become frequent guests modern bathrooms, because they are much easier to iron, aesthetic, with various kinds of design.But over time, these items can be damaged, losing its former neat appearance.How to make a repair acrylic baths with their own hands, without engaging the services of professional plumbers?

Common types of acrylic baths damage

  1. Mechanical arising from careless use of hygiene items.
  2. Chemical, under the influence of strong detergents that leave stains and other marks are not esthetic.

solve these problems, you can: Replace damaged bath for a new one.Or to repair acrylic bathtub with his hands, refurbished product at a reasonable price.

Subtleties repair

Before starting the "recovery" bath is important to determine the color of the product and the material from which it is produced.tone mismatch can greatly affect the outcome of the work done, and to alter one job twice is not very desirable!

Tools Required

During the restoration will need the following repair kit acrylic bathtubs.

  • A pair of rubber gloves.
  • polished disc or a sponge.
  • Pasta bath.
  • abrasive grain sheet 2,000 to 800.
  • liquid acrylic, to address the deeper chips.
  • drill with a drill 0.5-1mm.
  • alcoholic solution.
  • soft lint-free swab.

Instruction for beginners

  1. Professionals advise to extend the scope of damage, so that the clutch of the old and new material did not differ visually, with a crack in the depth and width must be increased by 2 mm.
  2. repaired surface is required to degrease with alcohol beforehand.
  3. Apply the mixture on the damaged area must be properly fresh acrylic must not rise above the old and be deeper than it.
  4. After repair chips of acrylic baths is important to close the completed portion of the film with adhesive tape and leave to dry for 6-7 hours.It is desirable at this time not to use the bathroom.
  5. After removing the protective film to treat the repaired surface rind, which is included in the repair kit to repair acrylic bathtubs.

make repairs minor scratches and burn-through

If the damage is deep, are superficial, then do a repair acrylic coating bath will be very easy and simple.

sandpaper varying degrees of granularity trimmed damage, first major, in the end - fine.After polishing the surface to be processed polish for acrylic baths.In such cases a plastic tub repair completed, but if you scratch deeper, it will not do without a liquid acrylic.

Remove the rifts

Cracks in the acrylic tub and occur when a heavy object falling or wear or other force majeure.They should be removed immediately after detection, so as not to result in deteriorating the entire article.

Instruments
Widget from SocialMart

cracks in the acrylic tub repair using epoxy putty.Actions are performed as follows: first, large sandpaper trimmed the damaged side, further drill drilled holes on each side of the crack to 1 mm.Soap solution is washed "blank" under the filler, which is embedded after drying hole.

Damage composition is aged for about 12 hours, after sanding area restoration.

How to Repair a bath acrylic with repair tape?

first part of the work to dry cleaned the damaged surface is similar to the above method, but continue to cut part of the repair tape, the length of which overlaps the crack by 1 cm on each side of the pothole.Removed the protective film, and the sticky side firmly glued to the crack.

is important to remove all air bubbles within the coating.Three hours to complete the setting will be enough.Use bath is prohibited, so that the liquid was not included in this period under the tape and not ruin all the work.

Repair of chips in the bath

How can you effectively lead plumbing in order, when the acrylic bath formed chips and even holes?

To fully restore functionality devices need to perform

repair chips acrylic baths in 2 stages.

  1. surface smooth out coarse filler, dried layer is polished with sandpaper.
  2. After repair the bath acrylic failed, the entire surface of the product is subjected to polishing.Brightens every corner, bathroom becomes a natural snow-white color, all the cracks and the Falcons are in the distant past.

When it comes to deep and serious defects of the hole is better to entrust the work of professionals in order to perfect the product has served the owners for many years.

For those who for the first time faced with such a task, it will be useful to view video repair acrylic bathtubs, where the example of one of the users described step by step all the nuances and major technical problems.

Frequent users

Questions How to repair acrylic bathtub so that the layers of material would not leave after a while?

This defect possible non-compliance with basic rules of installation and operation of the product, as well as an advanced stage of manifestation of cracks can cause similar troubles.When scratches or Oskol edge away from the bottom layer of fiberglass, you need to take special glue and glue the base before the repair bath.Instead, the adhesive can be used for fiberglass repair kit, which is sold in any shop.Using

during repair acrylic bathtubs video can be viewed in detail all the stages of preparation and performance features of the restaurant plumbing.

There is a saying - your eyes to fear, but the hands are doing!Let your bath will always be safe and sound, and the question of how to repair acrylic bathtub you know all the answers to the above, thanks to the detailed material.

instagram viewer