Metal grill with your hands : a step by step assembly instructions

Materials

for barbecue size 60h30h20 see necessary: ​​

• sheet iron of 2-3 mm thickness with dimensions of 60x60 cm;
• Trim half-inch metal pipe;
• Reinforcing bars Ø12- 4 pieces of length of about 80 cm for the manufacture of the legs.

Of tool is useful to you:

• Bulgarka a cutting wheel;
• welding machine;
• Drill and drill bits for metal 4 mm and 8 mm.
• Meter and pencil.

design

barbecue Barbecue Metal is a metal box with perforated walls, 30 cm wide and 60 cm long or more or the size of the barbecue depend on the volume at the same time loaded barbecue.By the duct bottom welded pipe cutter 8-10 cm long are inserted in the legs -. Reinforcing bars with welded metal glides.For the stability of the legs can be mutually seal the webs.

Metal BBQ

Brazier folding design that makes it easy to carry it in the trunk of a car.Metal for barbecue should have a thickness of 2-3 mm, the thinner the metal from fire and burns deformed, with a thickness of 3 mm design is too bulky and heavy.

Height barbecue traditionally does not exceed 25-30 cm, using birch charcoal ready enough height of 20 cm to adjust the position of the skewers over the coals, you can barbecue in the sidewalls of the grooves depth of about 5 cm. - This method allows to lower and lift the skewer.Incoming air in the sidewalls of the holes in the brazier operate one or two rows.

perform barbecue metal technology with their hands

1. metal sheet thickness of 2-3 mm is placed on a flat surface.If the sheet with a new technology grease - it is necessary to burn the gas burner.
2. right to perform the drawing sheet next barbecue marker.From the lower edge of the sheet back down a distance equal to the height of the barbecue and spend a line parallel to the edge.From this line back down a distance equal to the width of the barbecue - it is usually 30 cm again conducted a parallel line..Postpone the line height of the barbecue and spend the third line.From the lateral edge of the metal sheet lay a distance equal to the length of the barbecue.Spend a line and get the dimensions of the workpiece.
3. rectangular blank is cut by a grinder.On the borders of the bottom and side walls of the grinder gently make shallow inscription, in which bend the sheet in U-shaped structure.
4. From the remnants of leaf cut end walls in the form of rectangles.The dimensions of the side walls must match the width and height of the barbecue, plus allowances for bends on both sides and bottom.Through bends slightly as the preform nadpilivayut 1/3 metal thickness and bent at right angles.To the end walls of the handle are welded metal strip or rod.
   

   Construction metal barbecue

5. By U-shaped blank end walls are fixed by welding, bolts or welding zaklepki.Esli wall is attached, for the greater strength sutures boil on both sides.
6. resulting box upside down and put mark out holes in the side walls.To do this, conducted a longitudinal straight line on the side walls at a distance of about 5 cm from the bottom of the barbecue, on a line at regular intervals in the 5-8 cm marks the center of future openings.Using packed core centers, after which they were drilled with a drill diameter of 4 mm.Drilled holes ream to a diameter of 8-12 mm.
7. Turn the grill down and down is performed using the cutting disc grinders and triangular-shaped grooves on the side walls at a distance of 10 cm depth of grooves -.. 2-5 cm
8. to the bottom of the barbecue welded segments half-inch water pipe length of 8-10 centimeters.can play a role of support or serve as nests for the legs of the armature.Feet of rebar makes such a height that skewers frying meat were lowered at hand.It is possible to weld the bottom legs of the thrust bearing scrap metal, so that they do not fall into the soil.

Present barbecue design - polurazbornaya, her legs are shot, but the barbecue box remains intact.You can make a fully collapsible grill, fastening its components by means of grooves and latches.Its design is shown in the figure, and the assembly and disassembly of this barbecue is shown in the video.

Polurazbornaya design barbecue

Video - collapsible metal grill