Build Daily

Heater Overview

August 12, 2017 18:07

Homemade induction boiler - 2 of the embodiment

click fraud protection

Induction heaters are good that consume the least power compared to the other options of electric boilers for heating.However, not everyone can afford such a pleasure, especially for use in suburban areas that are rarely visited.This is due to the high cost of products, which can range from 25 to 100 thous. Rubles.In order to still indulge in such an electric heater and at the same time to save their own funds, be sure to make the induction boiler with his hands.For information on how to assemble at home, read on!

Contents:
  • idea №1 - Simple swirl heater
  • idea №2 - A more powerful machine

idea №1 - Simple swirl heater

The principle of the vortex heater

Firstcheck out how this option works heating and what is its advantage over the alternatives boilers.All the questions you will answer the video provided below!

description of the advantages and the operating principle of induction heaters
YouTube Preview

From the materials for the manufacture of home-made You will need:

  1. plastic pipe long with an internal diameter of no more than 50 mm;
  2. steel wire with a diameter of not more than 7 mm;
  3. 2 adapters for connection to the heating system (pipes);
  4. metal mesh with small cells;
  5. copper enameled wire;
  6. high-frequency inverter;
  7. insulation material.

prepare all the materials, you can proceed to the assembly of the induction of the boiler with his hands.First slice steel wire at 5-cm pieces.After that, close one side of the plastic pipe into the net and go to sleep cut the wire.The amount of material should be such that the volume was completely homemade "hammered" wire.Further, the other end closed metal grid, which will prevent the spread of the wire for the heating system.

When the filling is ready, you need to make your own homemade connection point of the vortex of the boiler to the heating line.For this adapter are fixed on both sides of the pipe by welding or threaded connection.

Next, you need to make the heating element of the device - an induction coil.All you need to wind on top of the pipe about 90-100 turns of copper wire.Be sure to follow the pitch between the coils to a homemade machine worked uniformly.After complete winding copper wire ends are connected to the inverter and, eventually, the boiler body can be assembled and suitably heat and insulate the conductive material.

Starting a homemade heater must be carried out only after the connection to the coolant - water.If you turn on the inverter without water in the casing pipe immediately melt and all your efforts will be in vain.

That's the instruction, which allows to make the induction boiler improvised at home.This home-made can be installed in any part of the heating system, but because of the not very attractive appearance we recommend to hide it out of sight.

clearly see the principle of operation of the device can in this photo:

The heating of the inverter core

As can be seen, the core inside the red-hot, which is due to exposure to electromagnetic fields.Tests of the assembled device suggested viewed on a video example:

Action electromagnetic field
YouTube Preview

idea №2 - A more powerful machine

to make a powerful induction boiler with his hands, only need to be able to use welding.In fact, the assembly technology is not too complicated, and it can handle any electrical, self-taught, and what you make after reading.

So, the materials you will need:

  • two pieces of metal pipes of different diameters;
  • copper enameled wire;
  • two adapters for heating pipes (supply and return);
  • heat insulating casing;
  • three-phase inverter.

drawing homemade heater as follows: A good drawing

As you can see, one pipe should be welded inside the other to get a hollow tank in the form of a cylinder.Also, using the welding machine is necessary to "embed" the two tube into the tank for the cold water and the hot output to the heating system.

Further, as shown in the diagram above, you need to wind the copper wire on the body of the induction of the boiler.Winding, as you know, will serve as a heating element and into contact with the coolant, it will be heated.On top of established design is necessary to pull the heat insulating cover, then open the water supply and test the system.


Worth also view a graphic video assembly instructions similar machine at home:
simple and at the same time a powerful electric boiler
YouTube Preview

And finally, we advise you toacquainted with a master class on manufacturing of inductive boiler tiles:

How to make home-made tiles?
YouTube Preview

Here we have provided 2 embodiment of the self-made induction boiler, heating the water by the action of an electromagnetic field.We hope that you now know how to make improvised heater at home, becauseBoth technologies have been "chewed" from A to Z!

Related items:

  • How to make an electrode boiler with his hands
  • How do independent heating apartments electricity
  • How to make a twisting wires

instagram viewer