Install vinyl siding with their own hands - a step by step guide

Install siding, if there is a project, clearly calculated the amount of material and the fixture to it, will be able to even a layman.Will be needed: a pair of saber (simple and metal cutting), ruler, hammer and level, Bulgarian, screwdriver, tape measure, plumb line.Successfully installed siding will last for many years, in spite of the cold and heat.Install Support will our article on how to carry out the installation of vinyl siding by hand.Stages are as follows: first you need to prepare the walls, then set the starting profile heater for installation of the main profile.In addition, we recommend to read about it, installation thermal panels with ceramic tiles and metal siding under a tree.

Also we advise to read about it, installation of thermal panels with ceramic tiles and metal siding under a tree.

10 gold recommendations

siding installation Always bear in mind that vinyl sading (ie PVC) increases and decreases with temperature change.To siding is not warped, be sure to take into account tolerances - read about the installation of crates under the siding.Please also read the installation instructions supplied by the manufacturer of the material.

can not attach siding directly to the wall: it impairs the movement of air, it leads to the formation of mold and mildew.For crates to choose well-dried wood.wood humidity is 12-15%.Or perform a lattice for attaching metal siding (suitable as if the walls of aerated concrete, brick or witty of aerated concrete, as well as in those cases when you need to perform the trim, using a heater).Wood treated ognebiozaschitoy.It is recommended to refer furring strips two feet from each other, and when the windy climates step is reduced to a few dozen centimeters.The depth of the lattice strips is determined by the presence of a heater.After attaching the panel so that the buckle locks no longer treat the panel.Once connected, the lock, the tension latch with external influences will be too strong and can damage the panel.

Use corrosion nails (galvanized, aluminum, steel) or screws, setting panel.Siding will last 50 years, if all fasteners zaschischenyot destruction.

To siding is not warped, be sure to take into account tolerances - read about the installation of crates under the siding.

attachment size is chosen such that they are immersed in the batten at least 30 millimeters in diameter on the heads of nails or screws are selected by 8 mm.Mounting set straight, will lead to the fact that the straps and stand up straight, deformed.Expansion evenly, but the extension is in direct proportion to the length of the original panels.You can not drive nails and screws to fasten close to the vinyl flooring.

uneven, bent nails, fasteners, screwed on the edge of the perforation prevents proper expansion strips, panels, warp the surface.It is required that the panel had free course, in other words, the nails should not touch obreshetochnogo layer before reaching him at least a millimeter.In case if you make it hard nails, use self-tapping screws.They screw up completely, spun at turn back.Select the mounting step - 40-45 cm

can not pierce it with nails and screws vinyl..The size of perforation holes, if you want to drive a fastening element side, you can increase the punch.If your edge is constantly windy, the hat Gvozdkov or screw lay rubber or PVC washer.Joining elements must also take into account the temperature gaps.

During installation, you must also make allowances for a cool environment.Heat means that the siding has lengthened, and at low rates, gaps need to be increased, as a warming strap stretches.It is best to finish all the work with PVC to sub-zero temperatures.

horizontal bar Center - start of driving in of nails, lead the process toward the edges.Or on top of a vertically mounted rails, going to the floor.After finishing mounting, you need to move the bar up and down if the course turns free, installation is correct.

Temperature gap is considered as follows: meter PVC siding increases, on average, half a centimeter every increase in temperature of ten degrees, and vice versa.This parameter specifies the manufacturer.

bladed panel put overlap, respecting the imposition of - at least 20 millimeters.Thus the seam is sealed: in order not to fall precipitation.Be sure that the straps are not limited by the established profile, they need to trim.

Sockets, PVC, where they joined the corner panel can not be sealed, as well as play-space.Attaching anything from the outside to the vinyl siding monitor to mount does not affect the mobility of the siding.

How to insulate siding siding

thermal protection does not form, because its function - to hide the room from the rain and wind.Wall insulation under the siding begins with a vapor barrier.Next in obreshetochny frame placed proofing materials.Next harbor wind-insulating material, and then carry out the installation of siding.Insulation of the house depends on the thickness of the insulation under the siding.

How do you know that a good siding?

sure way to check the siding on "aptitude" - to evaluate siding lock.Good siding snaps are not too heavy and dense and hard, but not free and easy.

Video - installation of vinyl siding