4 ways to pick up the bath higher

need arises often picked up the bath slightly above the level at which it is located.This may be due to the fact that for some reason the flow from it is not carried out properly, as the slope of a small or even negative.Another reason may be that the factory products have legs too short and the hosts uncomfortable to use.High growth of households can also be a reason for this decision.We offer you a choice of 4 ways to raise the bath higher.

What is the complexity of solving the problem of raising the bath

Weight any bath is made up of various components:

• itself bath.
• water poured into it.
• Weight bathing person.

When even the most conservative estimates the total weight of a full bath with 1-2 people located in it can exceed 300-400 kg.The entire load is distributed on all 4 legs, but their total contact with the floor area is unlikely to exceed 10 square meters.cm, which is 30 -40 kg per 1 sq.cm. This fact is perhaps the most important when you choose a bath lift.An important role is played by the material itself, from which the bath is done.

Describes how to raise the bath

Depending on the circumstances above, you can select one of the following methods to solve this problem:

• With the extension of the existing legs.
• As a result of the construction of the stand of solid materials.
• With mounted metal frame.
• construction of the pedestal for beautiful baths.

consider in more detail each of these methods in relation to the real conditions.

How to increase the bath, lengthening her legs

Most often bundled with standard tubs are provided for their legs, which are attached directly to the most sanitary design.At the same time, their length does not always satisfy the users.What can be done in the case when the standard font for the legs are very short?It's simple enough: you must purchase new screws which are longer.To do this, you need to collect one leg at home, and with it go to the point of sale, where to pick up the longer screws.After that, instead of pins, screw factory newly acquired and set the bath in place.

necessary when purchasing pins pay attention to their quality, because they are to withstand the weight of half a ton.This is the simplest method that does not require almost no knowledge and skills.It allows even raise design options baths without compromising their appearance.

Install bath on a firm and reliable support

Extend legs in the bath, of course, the easiest way, but it is much safer to build underneath a secure base from which a solid material.For this purpose, they can be used: wood, brick, paving slabs.It should be remembered that none of these materials are not able to withstand the load of the legs due to their small area.Therefore, to increase it is necessary to put under the legs of the metal plates of steel at least 3 mm in thickness and 100 cm2.

In addition, it should be remembered that the bathroom has a special water-logged "climate".Therefore, when choosing wooden coasters need to be accurately process antiseptic substances and arrange waterproofing.To this end, the bars can be painted and covered with a waterproof varnish.These measures will help protect the wood from rotting, delamination and the emergence of junk on it "life" in the form of mold and mildew.The only advantage of wood in this case is its ease of handling and, as a consequence, the speed of the task.

Choosing a brick or tile, you need to be guided by the fact that the product should always be whole without cracks, chips and other defects.In general, these materials are much stronger than wood, but only under the condition that they are linked solution.You can use and tile adhesive, but its reliability is poor.When mounting such a structure is necessary to raise the back of the bath for about 1 cm above the front, if the configuration does not provide its bottom slope.

Install bath on a homemade metal frame

If you have already learned to good use welding equipment, you can make a frame made of steel angle and pipes.You will need: welder, Bulgarian, corners and pipe.The cross-section corners and pipes should be large enough to support the weight of the bath.The design of the frame under the bath must provide maximum stability and durability.Frame made of such size that it rested against the tub all its facets, but could not fall inside.To bath held on the frame is more stable, and the water in it is not longer possible to use cooled with foam, which should fill the gap between the frame and the bathroom.

bath Planting on a pedestal

Sometimes tub bears the function of not only hygienic, but also is the subject of design and decor.Typically, these products have the original beautiful shape, curly twists, and often very short legs.What you want to do in this case?It is clear that any of the above-described methods simply spoil the entire beauty.The output remains one - if you can not lift the bath, it is necessary to raise the entire floor beneath it.Of course, to lift part of the floor - a task undoubtedly more complicated, but after the completion of all repairs bathroom will find a royal appearance.Built podium you can go out of the bath as a straight or curly step.They can even do a bit of a ladder.This option will allow you to bring in the usual bathroom special refinement and incredible originality.

main thing is if you live in a high-rise building, do not forget about the weight of the podium.To this must be added the weight of the bathtub with water and people.The load on the ceiling should not be too high, especially in old houses with wooden beams.To facilitate the weight of the podium is worth doing it is not monolithic, and use frame structures that decorate the pleasant pictures.Note that if the frame is made of wood, it will not sustain the weight of a full bath.Therefore, in addition must be made inside the rack, which evenly distribute the weight of the bath across the podium area.

process podium devices under the bath made of plywood and bars

To build a brick podium will need the following:

• saw or jigsaw.
• Hand screwdriver or drill.
• Hammer.
• Plywood and bars.
• Screws, brackets and other hardware.
• Building level.
• polyethylene film.

Work on the construction of the podium will be as follows.If your pedestal adjacent to the wall, and will not be in the middle of the bathroom, you should use the spirit level and a pencil to make the top edge of the layout for the future of the pedestal.The main floor under the bathroom carefully waterproofing polyethylene or more suitable for these purposes, an insulating material.You can additionally be used cork substrate.

Then you need to put plywood on the floor at the spot where you want to build a podium, and nail it to the floor with nails or dowels.After that, it is necessary to collect a solid frame of timber, which corresponds to the size and configuration of the future of the pedestal.Details are held together with screws and corners for greater rigidity.For bathtubs equipped with legs make special metal supports, which increase the impact area on the podium.The frame is sheathed with plywood and is made by any suitable under the overall style of the bathroom material room.

Lifting bath acrylic using brick or light concrete blocks

in private homes possible device podium not only wooden components, but also of brick, which is associated with cement mortar.This pedestal is very easy to decorate with tile or mosaic tiles.He did just enough.On the floor, draw the contour of the future of the podium, and spread it on bricks or concrete blocks.Then fill in the same material of the entire inner area.The entire structure is filled with concrete and level by level.After drying screed can impose podium floors.Creating such a structure makes sense for complex repair of a bathroom or during the initial construction.

some nuances when picked bath

As mentioned above, the baths are different, so depending on the material from which they are made, requires several different approaches in the implementation of ideas for raising theirto a higher level.

Cast iron baths, for obvious reasons, is one of the most difficult products.Compete with them, probably capable of only stone bath from natural rock.It is because of the very high weight to the cast-iron baths should be taken very carefully.

As baths of acrylic components, they can be lifted off the floor only by means of some parts of which are mounted in a wall.Exalted steel bath above standard level is possible by means of cement covering.And this tie is only where she will be a bath.In this case, you must make the right slope for water runoff.This can be placed under the rear feet of sanitary products every square tube, or the usual channel.In addition, you can use wide round washers, studs and threaded length in meters.In this case it will be enough to drill holes in the brick pedestal to the floor.Hairpin cut into four equal parts.They are inserted into the prepared hole and is filled with mortar.After it dries bath set feet on these pins.This design provides high reliability and stiffness of the sanitary device.

When you install bath in the brickwork is important to know that by raising the bath above the floor level, it is important to monitor compliance with its unwavering stability.It is under no circumstances should not wobble and wobble.Sami attachment for legs should have a very high reliability.Raising a bath at very high altitudes (over 10 cm), you should do a few steps, and in any case no one.Podium, which is covered with tiles in a wetted condition can be very slippery, risking injury when falling.To avoid such trouble enough to come up and set near a bath tub some reliable rail, for which you can grab in an emergency.It can also be used instead of the porcelain tiles, which is safer for the reason that it is not so slippery.

It is believe that this article has helped you to gain the necessary knowledge base of how to raise the bath above the floor level.It does not matter which option you choose, most importantly, remember that you need to strictly follow the instructions and apply the only high-quality and comfortable materials.This allows you to avoid various "unforeseen" and hand made ups, frames or mounting can operate without fear for many years.