What better to do on the slopes of PVC windows - plasterboard , plaster or plastic

Setting slopes as an important stage of the installation of windows

Slope - the inside of the window opening, the place is inserted into the window itself.When you have to change the box, you need to pay attention to the slopes, the higher the quality, the better the appearance of the whole.

when installing windows of PVC today offered the following types of slopes: drywall, plaster and plastic.

without any slope is the new and high-quality window will look unfinished and sloppy.And often learn about the slopes in the apartment repair or replacement of windows.Tom, the old slopes stood long enough without a crack, there is an explanation.Old window design had improved breathability.Because gapping cracks and ash pit, creating gentle slopes temperature zone.But the modern design of wooden and plastic windows have leaks.The air does not flow into the gap, which is just not, and slopes are between the outside cold and warm inside, i.e.the temperature boundary, which is expressed quite sharply.When you open the windows for ventilation, cold air falls on the heated slope, which is why he cracked.Also plays an important role condensate.

Plastering slopes for plastic windows

plaster mixture from which the slopes are made, it is not connected firmly to the PVC frame, and it will sooner or later lead to the delamination of the slope.The slope is not plastering materials, which would be a good thermal insulation properties, it leads to overcooling of the opening in the cold, the window itself.This causes condensation on a slope, and on the pane.

In the manufacture of plaster slopes takes a long time.As technology material is applied in layers, and each new layer is possible to lay down only after drying the previous one.Otherwise slopes will crack.The plaster, which is applied on concrete or brick, still a wall.Therefore, the slopes get cold and freeze in the joints of the frame.By the way, see what are now modern insulation windows technology, the most common technique - oknadena.

Plasterboard soffits

The same shortcomings and slopes of plasterboard, which still require a good mount.If the drywall sheet of thin plastic stick, the quality will not be at the height: it is time-consuming work with insufficient stability of gypsum cardboard and unreliability of the adhesive bond and leads to destruction.

thin plastic sheets are not suitable for decoration, although it is one of the easiest ways to finish slopes.Slopes in this case is not insulated, and it leads to freezing and condensation, and the method of bonding plastic leads to detachment of the compression / expansion of the material.

Widget from SocialMart

PVC Plastic slopes

now on building materials market can find a panel of cellular plastic.With mineral wool insulation, the use of mounting profile, fixing panels on the rail, you can use this stuff.You should choose the highest quality manufacturers.Cheaper panels over time, change color on the face of stiffening ribs visible, which in turn leads to loss of the overall attractiveness of the window, it seems artisanal decoration of the window opening at Quality construction window.

slopes MDF panels cost cheap enough, but, as well as the slopes made of drywall, do not have sufficient water resistance and the need for quality fastening.

have sided sandwich panels good aesthetic characteristics, but there is no sufficient rigidity.This is particularly undesirable when the wide slopes, as the slope will sag.

To date, produced two-layer sandwich panels and special plastic slopes, which are considered the most high-quality and practical to use, although they are more expensive than others.

Installation slopes of PVC plastic windows provide a good seal, guarantee the absence of cracks, create a sense of solidity and completeness.

important role in the overall impression of the room, and given to the junction of wallpaper and repose.The most expensive high-quality repairs will be reduced to nothing if they are seen at the intersection of the lagging wallpaper or cracked slope.Repair is also possible by means of the slope of PVC.Slopes PVC perfectly eliminate visual minus by changing the slope of a wooden structure in the plastic when the band is due to the difference in the thickness of wooden frames and plastic.Besides installing the slopes of PVC does not take much time, they have moisture resistance, are not afraid of direct sunlight, significantly transforming the appearance of the room.Significantly, in the case of damage to the slope of PVC plastic, it can be easily replaced.Due to operational quality and reasonable cost, plastic slopes gained much popularity.It is also important to properly install sill given inclinations distortions.

installation of plastic slopes

In terms of completed installation of slopes for PVC windows is the simplest.By the plastic as opposed to other materials, can suffer deformation up to a critical point.If the wood does not stand derailed seasonal temperature changes and deform without varnish protection, plastic quietly carries both moisture and temperature extremes.From a decorative point of view, the slopes may resemble textured finishes such as metal, wood.This is achieved by laminating a special film that mimics these materials.

installation of plastic slopes video