Tool box with his hands

present owner is always concerned about the safety of their instruments.Even a small set must be stored in an orderly, neat.A skilled master can collect container under their own tools and accessories.Here we will talk about how to make a tool box with his hands.Submitted photos and videos to help in the work.

outer box looks soundly and stylish, he immediately saysa serious approach to the life of its owner.Its dimensions (70h40h45 cm), that is, 70 cm wide, 40 cm deep, 45 cm in height.This is sufficient to accommodate the hand tool.In box 3 drawers and top hinged lid that opens the volume compartment.This box allows you to protect the instruments from dust, to organize safe storage.

• circular saw;:

  Tools Required

  following tools will be needed for the manufacture of wooden box

• milling machine;
• Grinder;
• clamp;
• hammer;
• clippers;
• file;
• hacksaw on a tree;
• chisel.

Step by step instructions for the manufacture of boxes for tools

optimal material for the manufacture of the frame - oak wood.This is an excellent durable material, which is durable and resistant to mechanical stress.It is better to build on - laminated boards 19 mm thick.This material has no knots and rotten inclusions.With conveyers cut strip width of 38 mm.

to when bonding the individual elements are shifted relative to each other in the first part a little drive in pinks, cutters removed his hat, and then acting on the tip of a sharp stuffed second board.

boards further coat with glue and fix.

Speaking at the junction of parts glue is removed with a chisel, but we have to wait for the adhesive has dried up a bit.

As a result, should get a detail 38h38 mm.Her face is polished.

Edge should be cut severely at 90 °, thus cutting off the piece of desired length, you can not forget about the cut-off angle.

This method will help ensure the accuracy of the cutting angle.Location

every detail marked to avoid confusion during assembly.

in every detail along the entire length is cut a groove, it should go strictly by the center.

Grooves can be made either by a stationary circular saw or a milling machine via.

On items that are designed for vertical angular frame supports, make a cross marking.

make another longitudinal groove in the rear corner detail.In the front corner support details, he does not need.

need to find the center, noting the point of intersection of the diagonals for subsequent attachment to the end of the blanks.

Next to the marked point drilled hole, the diameter of which corresponds to the diameter dowels for fixing (6 mm).

It is necessary to verify the compatibility of blanks.

blanks processed file.

freely collected in the frame make a mark, to subsequently extend the slots.

slots cut out a hacksaw on wood.

chisel remove all unnecessary.

Next wooden tool box is made in installments.First - the side walls, then - the whole structure, hereinafter - the drawers, in the end - cap.The side walls are made of birch plywood.

These blanks are needed for drawers.With the end of the sawed area.

Each blank is drilled for the mounting bolts.

observing accuracy, it is necessary to prisverlit prepared items.

For details, designed for attachment and separation of 2 drawers, run cuts at an angle of 90 °.

installing the components for movement to place boxes and fixing them, they gradually begin to bind.

Corners are cut plywood pieces, as in the photo.

walls of the lower boxes are attached to a sheet of plywood with self-tapping screws.

To one side is attached trained horizontal parts of plywood.First, it is done without the use of glue.

During fixation with the help of clamps should be checked diagonal sizes to coincide.

Drawers are made of plywood.

slots can cut it out or on the stationary saw, or by milling.

further need Forstner drill bit to make a hole.

Details drawers held together with glue.

side of the boxes should have slots for movement on fixed inside the slats.

strength to the side parts are held together with dowels, which are cut flush.

for reliability when bonding the small cloves partly driven into the surface of the front wall of the drawer, removed their hats.

attach the front panel to remove the drawers, looking exactly whether individual elements are arranged.

When gluing it is necessary to exercise extreme precision clearances should not be.

At the end of the upper frame made of plywood crate.

To make a precise cut under the angle 45 °, it is desirable to use a special tool.

Preparations for the frame are connected and fixed by gluing by means of a belt tensioner.

necessary to make the groove in the cover.

When fastening the plywood and frame parts are clamped and drilled with a thin drill.

round file form the end portion of the rotational member to hold the cover in the raised position.

retaining part fixed with thin cloves.Its diameter should be smaller than the hole to move the handle easily.

make a groove in the frame.

groove should not reach the corner portion.

upper frame is mounted on the anchors.

milling in the frame and the cover must be the same.

lid is secured by a hinge.

After final assembly all fixed, to provide high quality connections.

At the end of the tool box is polished and processed impregnated wood.

box manufacturing Video Tool own hands