Glue tile wall

to laying hold on tight and do not fell off, you need to know how to stick on the tile wall.

tile was, is and will be facing a very popular material of the walls and floor.This concerns not only the bathroom, but also the kitchen and the floor can be laid even in the whole house.

Benefits tiles over other materials is that it is resistant to moisture, durable, perfectly clean, aesthetic.

Preparing walls

Stick tile should be such that it is firmly held, do not slip, eventually it looked aesthetically pleasing.

Before laying the tiles in the bathroom need to remove the old cladding.If the old cover was also a tile, then it is completely removed along with the solution.

To simplify this process, the joints between the tiles clean out, after which the surface plentifully moisten with water.Leave the wall in this form for several hours needed to better absorbed water.

If the bathroom walls were covered with paint that is correct will it clean off.Use can be grinding disc for this.

Video:

If you can not do it, over the old paint made notches for better adhesion.

If the wallpaper, they also removed were used, wallpaper paste is washed off with water.Sami wallpapers for better waste, can be wet with warm water.If

walls blanched - wash whitewash: abundantly via spray process all surface water, allow some time for the impregnation, after which it can be removed with a spatula.

Conclusion: any old cover bathroom walls should be removed.

second stage of preparation - alignment

next stage - the alignment of the walls, you need to not watch the tiles will fall off.Prior to this, pre-wall must be cleaned and primed.

All cracks sealed filler.High humidity is a characteristic feature of the bathroom, so better to choose a filler with low moisture absorption.

To determine the amount of material that can be installed beacons, the level of which begin to level.

Video:

perfectly flat surface do not have to, as long as there was a large drop.

If the walls in the bathroom are very curves that can be used to align the drywall, which must necessarily be moisture-resistant.

Plasterboard attached to the walls with metal profiles, as fixing a special adhesive can be used, but because of the severity of the tile design must be reliable and durable, so choose the best profile.

Plasterboard is placed so that at the junction of no formation of the four corners.Despite the fact that the moisture-resistant gypsum board is used, it must be further treated with antiseptics.

To avoid problems with mold and mildew in the bathroom, before laying tile walls are also processed antiseptic.Next, the ground surface can be in two layers.

Put tiles

Laying tile begins with a markup.

order to laid tiles looked harmoniously and without bias, it would be correct to start laying the first row on the height at which should be placed second or third rows.

This is done so that the walls are usually not perfectly flat there if glue from the floor or ceiling, it may be formed skewed.

In the video you can see how the work is done by laying the tiles.

Video:

marking is done with the level.To the first row of tiles is not slid down, you can assign a metal profile or any other material as a support, acting as a guide.

Calculate the number of tiles in height is desirable so that the ceiling adjoined whole (nerezanyh) tiles, this point is not mandatory, but otherwise all the masonry will not look so beautiful.

If the ceiling is planned to be half, then perform these actions is not necessary, because the ceiling will hide all the bumps.

Using as a guide the bath rim, it will need to seal with tape to avoid scratching the surface.

glue application required two types of spatula: a straight and comb.On the wall of the glue is put through direct spatula, which stretched comb.

Glue is applied in small portions, under the 2-3 tile, so as not to dry out, so it is not necessary to coat the entire wall at once.

Also glue is applied to the tiles on the same principle: first direct spatula, then combed.Creating a rough surface needed for good adhesion to the surface of the adhesive.

To paste material, it is necessary to press, to check the level of the clutch and set crosses for even the gap between the tiles.

All subsequent rows are stacked in the same manner.If necessary, tiles can be cut.When all the tiles will be laid, we can begin grouting.

Video:

Put the tiles on the kitchen stove obkladyvayut

Most often, the kitchen put the tiles in an apron to protect the surface of the walls from water splashes, grease and grime.

If the main decorative wall covering will be wallpaper, it is best to lay the tiles, and then paste them.

If you already pasted wallpaper and plans are not worth their immediate replacement, then you should do the layout.

After this wallpaper neatly trimmed stationery knife, moistened with water, then swell wallpaper, and it will be easy to remove with a spatula.

On the wall you can stick the tiles on the same technology that has been discussed above.

If you use this method, the wallpaper can be soiled and torn, so it is advisable to perform the stacking and then glued wallpaper.

What if in a private home, the kitchen is the oven?In order to make it fit into the interior, and the cleaning was not a burden, it also draped tiles.

Since the oven is heated continuously during operation, you must choose the right tile.

It must be fire-resistant, heat-conducting - it is necessary to retain the heat when the furnace is running.To

tiles are not cracked, it must be durable.Right to choose the porous structure of the material, when the furnace is constantly warm up and cool down, the tiles do not disappear.

Normal adhesive is not suitable for laying such a coating on the stove.

Video:

can use sand and cement mortar, but it is better to buy a special flame-retardant mixture, so that later it was not necessary to glue the tiles have disappeared.

If the oven was covered with another material, it must be removed.Then, necessary parts and using nails attached thereto a metal grid.

for laying tiles on the oven used starting plaster and glue solution.Plastering the entire surface to be treated (top grid) and make it smooth.

When the plaster layer is dry, the surface should be primed.Then tile laid on the technology described above.

Put the tiles on the floor

floor tile is laid, not only in the bathroom, but also in the kitchen, hallway, balconies, and even in the living room.Tile - universal material to create a special atmosphere in the house.

Before you begin to direct the work necessary to prepare the ground.The first step is carried out the dismantling of the old flooring.

If the cover was a tile that does not falter, the tiles can be laid directly on it.It can also be put on the plywood or chipboard sheets.

next preparatory step is waterproofing.It is necessary, if the tiling on the floor occurs in wet areas (kitchen, bathroom), and, if placed on the plywood.

After that, you must make an even floor.The ideal situation would be for this self-leveling mixture.

In wet areas the floor must be further treated with antiseptics from the appearance of mold and mildew.

The last step will be priming the entire surface.

Paul begin to spread from the corner, which is always on the mind.Glue is applied to the floor on a pair of small number of tiles.For better grip the back of the tile surface can be wet by water.

Paul laid out in rows.Align tiles mallet.First, you need to glue all the whole tiles in a row.

To smooth the joints between the tiles need to use special crosses.At the end of the executed works makes grout joints.

Sticking tiles on a wooden surface

Laying tiles on wood due to the nature of the material does not happen often, so as not to watch the tiles will fall off.Tile can be installed on plywood, gypsum board or chipboard.

If you decide to glue the tiles on the old plywood or particle board, laid on the floor, you must first check their fitness: they do not creak, wobble, be skewed.

If there is at least one of these points, plywood or particleboard sheets are changed to the new (to open the entire floor is not necessary, you can do it selectively).

uneven surfaces sanded.Plywood and chipboard compulsorily treated with antiseptic, then on plywood and chipboard applied waterproofing mixture.

Top fit drywall to create a solid foundation.Drywall better to use water-resistant.

Video:

Secure the base can be, putting it on the plywood grid, after which the surface should be primed.CPD to improve the adhesion must be sanded, primed and then.

top of chipboard sheets can also lay the grid, fix and apply a small layer of glue.Once dry, you can put the drywall.

Next tile laid on the technology.