washing machine Atlant errors : error codes and fault washing Atlant, f4, f5, f9, f10 f13, f14, f15 washing machines Atlant

display code

indicator signals (with no display)

What does the error

Causes Error

What

door

burning indicator LEDs 1, 3 and 4

fault hatch lock

door is not completely closed or skewed.

electronic lock on the door is faulty or the electrical circuit broken.

disrupt the control module.

Check hatch closure density.

Rate electronic hatch lock function, as well as check the associated wiring.

Check the control unit and, if necessary, replace it with a new one.

None

light of the four indicator diode

formation of excess foam

Wrong choice of the type or dose of detergent.

Improper wash program (the amount of water excessively).

Correct dosage of powder or choose other means of brand.

carefully choose a program for a specific type of tissue.

Sel

Off none of the four indicator diodes

problem with the interface module

Broke selector responsible for the selection of programs.

Ensure selector malfunction and test controller.Replace the interface module.

F2

LED Lights 3

problem with the temperature sensor

sensor itself is defective or damaged associated electrical networks.

disrupt the control module.

Check the operation of the temperature sensor and the integrity of the wiring, replace the sensor, as well as test the control unit, and in case of fault replace it.

F3

indicator lights 3 and 4

problem with the heater

Broken heater or were damaged in the associated wiring.

disrupt the control module.

assess the integrity of circuits PETN and its performance, replace faulty components.When a fault is detected the control module to replace it with a new one.

F4

Lights LED indicator 2

problem with drain

pump stopped working.

violated patency of the drain assembly (hose kinked, incorrectly installed or clogged).

The pump has got a foreign object.

disrupt the control module or there were problems with its electrical circuits.

check whether the drain pump (the detection of breakage replace serviceable), and whether the system is clogged drain.If necessary, clean the filter, remove the foreign object from the pump, spread or attach a hose.

Examine the control module and its wiring.

F5

Indicator Light from the diodes 2 and 4

problem with the water in the machine set

The pipes no water or her head is too weak.

violated patency Bay system (Hose Clamp, incorrectly installed or clogged).

has worn the filling valve.

The chain connecting the filling valve and the control unit, there was a break.

disrupt the control module.

Ensure that the valve is not closed, and the water pressure is normal.

Rate patency Bay system and depending on the situation properly connect the hose, remove the blockage, clean the filter.To find

with a tester wiring breakage associated with a filling valve and check valve contacts.

If necessary, the valve must be replaced.

Check the control unit and, if necessary, replace it with a new one.

F6

burning indicator LEDs 2 and 3

problem with reverse relay

switch stopped working due to overheating of the winding, disconnecting the contacts or breakage.

Check relay and, if necessary, replace defective parts.

Check the engine.

F7

indicator light 2, 3 and 4

problem mains

electrical parameters are not suitable for cars.

has worn a noise filter.

disrupt the control module.

Rate Tester using the network settings and adjust them.

Check interference filter and, if it is defective, perform the replacement.

Check the control unit and, if necessary, replace it with a new one.

F8

Lit indicator diode 1

problem with filling the tank

Sealed bottle broken.

inlet valve stuck in the open position.

has worn pressure switch.

Having problems with contacts or circuits pressure switch.

disrupt the control module.

Verify balloon integrity and efficiency of the intake valve.

Check the pressure switch and the condition of its wiring.

Check the control unit and, if necessary, replace it with a new one.

F9

Indicator Light from the diodes 1 and 4

problem with tachometer

Broken tachometer or engine.

There were problems with the wiring or the motor terminals.

disrupt the control module.

Rate performance tachometer, then the motor, and then check the wiring that connects these parts with the control module.

Check the control unit and, if necessary, replace it with a new one.

F10

burning indicator LEDs 1 and 3

problem with locking hatch

electronic lock on the door is out of order or the electrical circuit broken.

disrupt the control module.

Rate electronic hatch lock function, as well as check the associated wiring.

Check the control unit and, if necessary, replace it with a new one.

F12 ​​

Indicator Light from the diodes 1 and 2

problem with the engine

faulty engine, appeared in his winding open or broken pins.

disrupt the control module.

Rate Motor state and its winding.If the engine is found non-functional, it should be replaced.

also important to check the control unit and, if necessary, replace it with a new one.

F13

indicator light 1, 2 and 4

Different fault

emerged damage electrical circuits or contacts.

disrupt the control module.

Check wiring and main components of the machine.Troubleshooting sections and parts replaced.

F14

indicator light 1 and 2

problem with software

There was a crash software.

Replace the electronic module on the defective parts.

F15

-

Water leakage

violated sealed tank.

damage the cuff hatch.

compromise the integrity of the drain system elements.

Make sure that the tank is intact and not damaged cuff hatch.With their failure to carry out the replacement of these parts.

Check the tightness of all the units responsible for the discharge of water.Damaged pipes and hoses replace whole.