Choose manual mill for wood - all the features , models and types

Hand mill is a tool indispensable for anyone who loves pomasterit.If it has the necessary equipment, it can be used for processing non-ferrous metals, composites, artificial stone, Plexiglas, plastic.To hand-mill was comfortable for you, it is necessary to choose correctly.

What can manually router

With a router you can make a lot of different operations:

• perform direct or figure-shaping part edge;
• recess slots for accessories;
• rebating;
• resurfacing;
• thread connecting spines;
• drilling holes;
• rough alignment, length blanks;
• manufacturing spiral or longitudinal grooves on the legs, baluster, etc .;
• carving, engraving (sculpture or mural);
• fit furniture laminate;
• cutting grooves, seams, splines.

upper router

Types Milling

choosing the router, which is necessary for you, you should decide its view that there are three:

• top;
• edging;
• lamellar.

Upper routers can be fixed and submersible.Represent the upper motor having a milling depth adjustment by moving up and down.Position the cutter it will have to change, do not turn it off, which is very difficult, especially for beginners.Ease of submersible version is that the engine slides along the rails, and thanks to stiffer springs, you can raise and lower the cutter on the job details.This device greatly facilitates the entire work process, from which even beginners easier to handle.Examples pretty good upper routers can cause Makita RP1800 F, Ryobi ERT1400RV, Protool NRP 90K and others.

edging mill

Edge mill, as is clear from its name, is mainly used for turning the edges and chamfering (for example, Bosch GKF 600 Professional, Makita RT7700C et al.).

With lamellar router slots are made, by means of which connect parts of the product (eg, Makita 3901, Ferm FBJ-710, etc.).

Jointers

Selecting manual router

To make the right choice you require the type of router, you should evaluate the most important of its characteristics.

Power

Routers are divided into heavy (more than 1200 W), the middle (of the order of 1100 W) and light (750 W).In domestic purposes it is sufficient milling medium and light level.

Speed ​​

It is on this parameter depends on a set of materials with which the router is able to work: the smaller the rate, the more accessible should be materials that he can overcome.Revolutions typically can range between 7 and 24 thousands.

switch

An important point that is often overlooked.At Fraser must be protected against accidental start-up and locking mechanism.If the latter would not, then the switch will have all the time to hold that will interfere with the operation.

Tsang

The best types of steel collet cone device.It is desirable that it is made of hardened steel, which guarantees a long life expectancy throughout the collet.

Dust extraction Dust extraction set

now almost all mills.The most efficient operation is provided by a built-in dust extraction.

Sole Sole is a critical component of the device is made of die-cast metal.In the highest quality milling tools soles cast.At the base support attached guide components and vertical rods.Soles should be closed with wooden or plastic bezel.

Boom mechanism

quality rods determines the performance and functionality of all the mills.The head part should fall on them smoothly and effortlessly.

Accessory items

In addition, it has been listed, the choice of playing the router and other important details.

use the router in the rough fitting is a very rare thing.Most often it is needed where accuracy must be meticulous.This is where it becomes very important role of the guides that are included in the box.

Parallel focus to be maintained on the router equidistant from the workpiece over its entire length.It is very important that it is made from high quality alloys, and the place of its contact with the workpiece has been isolated plastic bezel.

circular plate having a small ledge and calling sleeve (copying ring) must be inserted into the opening of the sole.It is necessary to pay attention to the ease of fixing it.Ideally, the design must be provided with a quick-release mechanism.This will avoid unnecessary movements during positioning parts.

Thanks angle stop , can be made up of the workpiece.The workpiece is above the template, whereas the milling cutter during operation based on a specially provided for the probe.When buying you should clarify whether he has control.