Setup and Installation of shutters : Step by step instructions and video

elements shutters

Technology installation of roller shutters

1. Prepare the side guides.With the help of a marker and tape measure to mark out their holes.For this purpose they are placed in pairs on a flat surface and a mark holes 10-15 cm from the guide rails and edged along their entire length at equal intervals of 40-50 cm. For surface mounting-type of shifting closer to the outer edge of the guide.Drill hole Ø 8 mm.For outdoor installation drilled through both sides of the tire, while the top is further ream to a diameter of 11.8 mm for the installation of decorative caps.
   

   Marking and drilling the holes for the consignment and a built-in installation

2. Preparation box.Is applied to the box cover and through said cover reams two holes on each side of 4.2 mm in diameter.These holes will be installed after the installation of rivets rolstaven.Rassverlivayut holes to secure the box.Their location depends on the type of installation: Surface-type rear, top and built for both planes for kombinirovannogo.Diametr drill - 8 mm.Vysverlivayut correct diameter hole for the drive.For surface-mounted boxes are cut at the junction of the guide with the help of wire cutters and pliers.Assemble the box and guides.
   

   Preparation box for shutters

3. marking fixing holes.Apply a frame assembled to the opening shutters.When surface mounting all elements of construction must lie on the wall, framing the doorway, with the built-in type of installation - be on the side and upper slope.Check the vertical guide and horizontal ducts, as well as collate diagonally - they must not differ by more than 2 mm.Vypolnyayut marker or drill markings previously drilled fixing holes in the wall or soffit.
   

   installation guide and mounting frame

4. Drilling mounting holes.Take the enclosed frame shutters from opening.By this marking holes drilled in the wall or doorway.The concrete wall set dyubelya.Delayut hole for the drive.Its diameter ranges from 12 to 20 mm depending on the type of roller blinds, it is necessary to clarify the product is not in the passport.In the opening set in pruzhinu.Esli protective shutters are provided external closures - mark out and drill the holes in the bottom of the guides for their fix.
   

   Drilling fixing holes

5. frame mount.Peel off the protective film of the rear wall frame.Put and align the assembled frame on the intended place for him.Align the marking hole and once again check the horizontality and verticality of the guide duct, and the distance between them.Krepjat frame screws using a screwdriver.
   

   Installation and mounting frame (surface mounted)

6. mount controls.For outdoor installation controls are fixed inside the building.Mark up the marker hole on the wall, and fix them drilled and guides coiler.
   

   Fixing guides cord

   

   Mounting bracket for guide

7. Installing fabric blinds.Distance rings on a perforated shaft expose equidistant increments of 40-50 cm. At the end profile Rolling canvas mounted manual crossbars on both sides.Plant fabric blinds from the top of the shaft in the guide rails.At the upper edge of the roller shutter web exhibit extension springs, zakrpelyayut them in perforated holes of the shaft.
   

   Setting Rolling web

8. Install the cover box, fasten it to the studs using a rivet gun.Take off the protective tape from the exterior surfaces, remove dirt.Install stops at the end web profile.Technological holes closed with plugs pre missed their silicone sealant.
   

   sealing holes and installing plugs

When installing shutters is necessary to observe safety, use only the power-good and stable ladder.The work is more convenient to carry out a team of two or three people.Connecting electrified drive are best left to a specialist, especially if you do not have the skills to electrical work.

All the installation of roller shutters with their hands shown in the video.

Video - installation of roller shutters with his hands

Thus, as you have seen the installation of roller shutters with their hands - it's not a difficult task, which can perform any cottager who exert some patience and diligence.