Block -house with their own hands - mounting technology

Internal and external finishing block house

for interior decoration uses wooden block house (link to article wooden block house) of smaller thickness compared with a block house for the external cladding.It is accordingly due to the fact that the outside wall made of wood have to endure various natural phenomena, extreme cold, high humidity, direct sunlight.And in order to withstand the harsh regimes, namely their differences, a more thick layer of material.

second difference interior trim from the outside is the method of attachment to the walls.When interior design can be mounted plate block house directly on the wall without creating a crate.This is convenient because you will not reduce the inner space, and in addition, you also save time and money for materials.For exterior trim frame is needed to make the layers of insulation and wind protection.
uses a lot of different tree species for the production of wooden block house, which is used rocks and how do they differ, you can read in the article Wooden block house.
There are several classes of block-house:

• «Extra».This class is the highest quality and therefore the most expensive, as there is not allowed defects, cracks, chips and knots.The surface is ideally smooth, high-quality processing.
• «A».The following class has a discharge permit from perfect flatness, sometimes may be small mechanical damage, the presence of small knots, darkening.
• «B».It is used for exterior trim, as this class has allowed visual mechanical defects, knots, splits, cracks.
• «C».Admitted bark residues, traces of mechanical damage can be significant, cracks, browning, knots medium diameter.

choose classes A and Extra For interior decoration, more optimal is the "A" class.The reason for this is its natural, that does not create doubt that the walls of the natural log.It looks like an extra class in finishing so pure and integral, that is not associated with the usual structure of the framework.Under the outer lining their own hands blockhouse class is well suited "B" or "C".The choice between these classes depends on personal preference and financial volumes, which are directed to the purchase of material.

acquisition block house

can buy a block-house is not treated with special antiseptic compounds, it will save money, but in this case you will have to spend their own hands processing.Otherwise, the material is protected from moisture, bugs, mold and mildew.The treatment solution is not difficult to carry out, it is done by a simple roller and brush.Roller stain easily accessible place, and after a brush painted joints, corners that are not to paint with a roller.

qualitative difference between serial processing and handling, which can make the most is the following: to improve and enhance the positive properties of the material of the plate in the manufacture of chemical compounds are treated in special pressure chambers, the best type of processing is vacuum-hydraulic.This process consists of treating flat workpieces in a pressure chamber where a vacuum to remove air and with it the moisture is not required after the solutions under hydraulic pressure supplied to the chamber.This is due to the influence solutions under pressure in a closed chamber, the composition penetrates into the wood to a depth of 5mm.

Therefore, when buying processed block Hausa specify what kind of treatment he underwent.After all, a simple brush and roller treatment, you might as well can produce on their own.And if possible, buy plates, past the vacuum-hydraulic treatment, do not take the money because such a material will last much longer, retain its positive properties on the time it will be longer.After the acquisition proceed to the wall.

Setting block house with his own hands

Mount Technology blockhouse inside

home Interior decoration starts with an assessment under the lining of the walls.If your walls are straight, they do not require crates, can be installed directly on the wall plate.But if the walls do not allow, it is better to carry out the installation of the frame.

Step 1: Install the frame. Crate in this case, involves the construction of a vertically attached to the wall, and deducing the level of the wall bars.If you prefer not to cross, and the vertical method of mounting block house, you will need to do across the crate, parallel to the floor.

Just need to identify places where there are outlets outlets, circuit breakers and other electrical, to make cut-outs in the wall before installation.The bars for the frame can be fixed to the wall like a simple nail, and mounting straps.For removing the carcass on the level will have to enclose the chips under the frame bars.After you create a frame, you can proceed to trim the block house with his own hands.

Step 2. Start lining block house. cladding technology does not contain any difficult processes, so the major difficulty for the person who assembles, not here.The first plank vymeryat, saw off on the size and attached to the frame by any method selected from those listed in Article Wooden block house.

Note.To the plates in the joints between the moisture accumulation was not necessary to fasten the block house groove downward, and upward spike.

Step 3. Compliance with the inner corner of the lining.

If you decide to do an exact imitation of a log house, you have to make a joint in the inner corner to overlap one edge to the other, as shown in picture 6 (simulation log) while trimming the edge of a roundness for a snug fit.A simpler way to install the technology can be called a block house on lath with straight joints in the inner corner, which you can then close the plastic of the corresponding color area.

Another way - this is the joint at the inner corner of the two plates by trimming the ends under the angle of 45 degrees.If you do undercuts on both ends of the trim, the plate nestle close to each other and the joint in the corner looks quite beautiful and aesthetically pleasing, it does not need to overlap area of ​​plastic.With
angles need to decide in advance to know how to measure and cut the first plate already.After the installation of the first plate, set firmly stykuya, the next plate, align, fasten.And so to the full coverage, keeping the joint in a corner.

mount technology block house outside the house

external finish is no different from the inside, but to build a reliable insulation and weatherproofing.It further will be discussed, as corner joints technology described above, and facing mounting methods can be found in the article Wooden block house.
Note.Before installing the block-house on the former should be given soak the material in the environment in which it will be.At time 4-5 days.If interior - indoor, outdoor - under a canopy.

Step 1. Choosing and buying a heater. Before installing the carcass pick up material for insulation, get it, and on the basis of the size of the width of the sheet set vertical furring strips.So it will be less time-consuming cutting of insulation, and therefore save material itself.
Step 2: Mounting battens.

Before installing the frame wall hooped layer vapor barrier, then made the frame assembly.Then, as shown in the image 10 (installation of external cladding technology), we are paving between the bars batten insulation sheets, fasten them with screws or staples.Then stretch the layer of the windshield, fasten it to the batten bars.

Step 3. Secondary crate. next step needed to create an additional layer, keeping you warm and create a separate section for the withdrawal of moisture, this is a secondary sheathing, consisting of smaller bars, which are mounted on the primary crate as you can see in the image 10 (installation of external cladding technology).

worth noting that you can not do secondary crate and mount block house directly on the primary crate.But in this case you will not have the inside of the ventilation and possible accumulation of moisture, which adversely affects the finish.It would therefore be better spent force and some of the money for the installation of the secondary sheathing.

Step 4. Installation of a block house. The final stage of mounting the lining - set the block house with his own hands on the frame.It should be repeated that make installation a block-house is necessary to spike up.The external finish is important because after the rain in the joints can collect moisture, which adversely affects the natural material.fastening methods can be selected more convenient and suitable for you in the article wooden house block.

Select mounting method, and proceed to measurement of cutting and block-house in accordance with the length of the wall.It is important to measure up to the height of the two edges of the wall, so that it was the same in the end mounting block house does not appear wedge.If you have a difference in height between the two edges, so it is necessary to bring the level.You will need to lift or height respectively simmered one side of home plate block house to start finish straight.

indent, which can remain not covered in the case of uneven walls, it is necessary to leave the bottom, its finish can be done after.To do this, measure up and mark suitable plate, then cut off at the desired angle.This is a difficult moment, so take it with a principle 7 times measure - cut once.

Note.Outside corner is on the same principle as the inner loop only, for example, the same angle of 45 degrees at the ends, only tilting in the opposite direction.If the joints are straight, they can close the decorative plastic corner, already outside.

about mounting block house

Installation panels are usually in the summer, when the weather is stable.This weather factor is very important when installing the block-house.Accordingly, only the interior of houses is carried out in the winter time of the year where there is a good and constant heating is kept stable level of humidity and temperature.

before purchasing materials, all you need to calculate, determine the choice of the block-house, to make in general the draft plan of action in order.Then it will be easier to coordinate their actions and to make installation of the block house with his own hands.

List of tools for editing block house

• Jigsaw or handsaw
• screwdriver or universal drill
• Hammer
• Construction staplers and staples (if necessary mounting windproof film, vapor barrier, insulation)
• Roulette measuring, level building

list of materials for the installation of the block-house

• panel block house
• Putty
• Corners plastic
• Screws and nails
• Reiki and bars under the framework
• Vapor barrier, insulation, windproof membrane
• clamps (when choosing the appropriateinstallation method)