How to make a strip foundation - the rules of construction of pragmatism

Building a foundation of tape - why this choice?

Strip foundation is considered one of the most common types and is a reinforced concrete strip that runs along the entire perimeter of the building.Bookmark it made under the outer and inner walls of the building, with all the same cross-section is maintained.Today, the design was widely used during the construction of outbuildings, frame houses, garages and fences.

tab strip foundation is based on the fact that it is mounted only in those places where the actually required differs from other types of foundation slab and melkozaglublennoy.Often, this type of structure can be called a forced option, because it is used only in the construction of buildings on slopes, where strong support is particularly important in the deep layers of the earth, which are not subject to creep.

tab strip foundation - the nature of the work

Undoubtedly, the device strip foundation with his own hands - it is difficult enough, but do not always have to resort to it.Not all buildings suitable base such as fences too, where it is so often used this technique may have other solutions.Options when mounting is possible on the supporting pillars, do not cause any problems, and does not affect much on the ground.First of all such structures include mesh-netting, wooden fence, steel sheet and TSPVS.

, as a result of a strong foundation becomes useless thing, not necessarily concrete pillars to build them, ie,just do not need it, but the very activity only take you time, money and effort.In the case, when your choice was the construction of strip foundation, the video on our website will help you better understand all the intricacies.

Wondering how to make a strip foundation, be prepared for the fact that this option can not be called economical.After all, to be ahead of inspiring amount of excavation, as well as a wide variety of materials used, laborious construction, a lot of weight and longer work.

But this type of foundation has a number of advantages, which include the ease of technology, though time-consuming, as well as high performance.In our video archive we build a strip foundation, which willingly tell nuances.

How to make a strip foundation - especially all the stages of work

Before you begin construction of strip foundation with his own hands, it is necessary to prepare the trench.For this is done counting, planned direction and the contour of the foundation.All this is something fixed, such as pegs, between which the cord is pulled.Only then dug trench depth is determined by the capacity of the future buildings.On average, this figure is around 40 cm. Digging a trench remember that all of the walls should be strictly vertical, for controlling this parameter, use gidrouroven.

Next you need to clean up the soil and sandy base, create a concrete mix, making formwork assembly on a booster cushion.The technology of construction of strip foundation is not too complicated, but it requires greater attention.For a start it is important to dig a pit, and do soil compacted.Here you will be special tamping.

At the bottom of the pit a sandy pillow.To properly perform the device strip foundation, the video at the beginning of the article is waiting for your viewing.

Sand can rammed itself or spill it, to speed up the process.The next step is to install the formwork, it is assembled from readily available materials, or create a pre-engineered, sold on stroyrynka.This step is important because right now creates a waterproofing, which is not the last element of importance for the whole process of how to build a strip foundation.Running it most of roofing material, lined with two layers.

to create formwork required calculation of the width of the foundation of the future, this figure will also depend on the weight of the future building and its geometry, however, and here is considered optimum value of 40 cm. In width, we have decided, but height has yet to consider.To the entire element turned out the same height, the formwork tensioned cord, which will mark the level to which to pour concrete.Themselves wall formwork must be above the pit, so that the mixture is not spilled over the top, and the construction itself was holding internal stress generated solution.

Continuing production of strip foundation, you can begin to install the reinforcement cage, if it is supposed to.Assign rebars you can use binding wire, which is convenient and easy to use.The frame should be present based on a certain number of rods required diameter (12 mm).

Next passes pouring concrete assembled structure.This is done in layers, each layer is compacted and tapping piercing the air outlet.By filling the formwork up to the marked level, is to solidify the foundation, you may need a month.In this article we have tried to succinctly describe how to make a strip foundation, it remains to wish you success in your work!