Choosing the best fillings in terms of price and quality

Quality finishes of walls dependswhat kind of brand acrylic finishing putty used.The sale represented a wide range of products from different manufacturers, and it is important to make the right choice, the coating retains its original performance properties for a long time.But what a good finishing putty will allow to achieve the desired result?Let's compare the products of different brands.

What are finishing putty

mixtures shpatlevanija walls are dry and divorced, and can be made based on a variety of materials.This should be considered when choosing the best putties: Each material has its advantages and is suitable for performing a certain type of work.

For example, it is easier to carry out the application of the finishing plaster putty and cement mix is ​​much stronger and more durable, though it is hard work.If the layer of gypsum material laid on the surface of the cement walls, it is better to create between them recommended primer layer - and that additional cost.The question of whether the walls should be primed after finishing putty, also affects the value and quality of the material.

As for brands, the most popular among Russian consumers are:

• Knauf;
• Ceresit;
• Ekogips;
• WeberVetonit;
• Sheetrock;
• Snejka.

Who is winning popularity price-quality

Studies show that the finish plaster walls under the wallpaper using a dry mix any brand gives the same result.All of these materials by dissolving acquire the same thickness, do not contain any lumps and foreign matter.Stirring finishing putty on the video is usually cut, in fact, this process takes 5-15 minutes: during this time the mineral additives in the mixture dissolved.

differences between materials of different manufacturers are shown in finishing putty wall surfaces.Thus, the least effort during application requires finishing putty Vetonit, others require a certain level of preparation of the master.The most dense solution is Snejka - it causes serious difficulties in working with the material.

disadvantage of a number of mixtures - high curing speed.Materials based on dry plaster sometimes directly in the container, before puttying walls finishing putty finishes.To avoid the trouble, it is recommended to prepare the mixture in a small volume.

Widget from SocialMart

different for different grades of materials and time is drying on the wall surface.So, finishing putty Vetonit 1R + from producer hardens within 4 hours after completion of the work, its sister KR same firm - 7 hours.Total required 2.5 hours for complete drying of the mixture CeresitCT 126, 3:00 - SnejkaAcril-Putz.EkogipsAlciSaten Putty hardens after 6 hours, and most of the time needed for drying KnaufHPFinish- even a day, it is not suitable for further processing.Regarding the finish plaster hardens rapidly Shitrok - from 3 to 8 hours, depending on the climate conditions in the room.Naturally drying depends on the temperature and humidity of the room.

After drying the mixture of the surface of the walls will be overwritten.At this stage, the most difficult to work with materials from Knauf manufacturers, Snejka, Ekogips.The rest of the mixture, especially finishing putty Vetonit, demonstrate good compliance.

In general, the best finishing material in terms of price and quality is the Sheetrock.The worst result - at Knauf.This mixture dries for a long time and is poorly grout.At the same time, the more difficult it was after finishing putty sanded walls, the smoother they become - however, perfectly ironed surface can not be considered indisputable advantage.

technology application and verification of the quality of a lamp defects

For mixtures of different manufacturers applied to the walls of the same technology.After preparing the walls of the base layer is created, sometimes it can be reinforced with a special mesh - it takes to finish a layer of putty is not collapsed together with the base, if the surface is very uneven too.

first composition is filled with cracks and potholes, which use small spatula.Then triturated composition throughout the wall surface.If the surface has no significant shortcomings, it is better to proceed to the second stage, using a wide spatula; then finish filling of walls and ceilings will be completed faster.When the first coat is dry, put the second.

Check more qualitatively performed puttying walls finishing putty can using the lamp: in the twilight of her at an angle relative to the surface, and if there are shadows - this is evidence of irregularities.Consequently, the work is not yet completed.