How to lay tile on the wall : Recommendations for the layman

As pokleit tile floor

tile is divided into 4 types (classes) on the level of strength:

1. weak.For the bathroom.
2. average.
3. sufficiently strong.
4. Heavy-duty.It is used for laying in the street.

feature floor-laying technique similar to the laying of the walls.The principle is: obmeryaetsya point of reference in accordance with the vertical rows and put tile.Special sealants or cement glue seams are sealed with a rubber spatula.If the seams are extremely broad, from 3-5 mm, in the adhesive mixture, add sand to make the structure even more robust.

To obtain perpendicular wall line that will reach the opposite wall, you should attach a corner and stretch the tape measure.

For angles to cut tile very carefully, then sticked to the ranks of the tile on the floor appeared symmetrical.To work is to start from the far corner of the room, and the cut edge of the tile laid on the floor.

How to put a tile, so that it is easier to go well and at the same level, you need to tap a rubber mallet to strengthen.As recently tiled walk is not necessary, or put on top of the board, on which will become a walk, until then, until the tile is dry completely.

to crop the form door jamb on the tiles using kafelerezku.To do this, put the size of the door frame on the tile with a pencil, then propylene and pliers to break off the pre-cut piece, and then you can start glueing.

recommend that you put as much as possible and apply the sealant should be a far corner.

How to lay tile on the wall

strict technique of laying ceramic tile involves laying first floor, and then the walls.But there are other cases:

1. When tile walls pressed against the floor tiles.
2. tiles on the bottom row is glued with a small omission from the floor, so that after it was possible to pour the cement and adhesive mortar for gluing of floor tiles.

Repair in the bathroom, in particular lining is customary to begin with the placement of decorative elements, because they are after facing will be very difficult to move.Such an element can be a mirror.is measured on the wall with a margin of 1-2 cm For its placement, then the tile is glued to the quick-drying glue.Small incisions can be tile, as in places such as under the sink, mirror and cabinet will not see them.

But suddenly, you decide to revet by the rule, you will have all the tiles to make an incision, determine the center of the object, and each tile strike froze.

Much better looks a tile, than cut.Therefore, from the glue the most visible to the inconspicuous corner, there will be placed sliced ​​pieces of tile.In the first row, you can begin to start using frogs that line the joints between the tiles.The only thing, do not forget to remove them within an hour after application, otherwise they wither directly on the wall and glue.

Layout

must be such that all the rows of tiles on the perimeter converged.When marking

important temperature control, as it affects the cladding process, such as sealant or fugue besides it has a certain color temperature requirements.Speaking of color fugue, the classic white color can be painted any color to your desired.

Important!How to glue tiles , when you are not sure about the size of the cut?Not at all, only with a well-metered sizes!

on the back of the tile it is important to strike a place for electrical fixtures.Drill can be punch.As for gluing mirrors, it is glued to the mastic, it is important only to the pre-gluing the tile surface and the seats were dried.The glueing also use crosses perpendicular to the wall, in order to align the edges of the tiles.After gluing all the crosses placed in the normal position.bonding strength is provided by rubber devices that can be crowded for uniform stacking.

Freese

Set as well as other ceramics on the walls with plastic crosses.In the corners are often frieze has to be cut, but the image allows to attach and elsewhere

How to lay tiles on the outer and inner corner

trim blue color used when finishing these angles (strips of plastic, which creates an aesthetic appearance corner).

Trim cleverly and adjacent to the wall and floor tiles.The level of control over the laying of the series becomes optimal.The smoothness of the first row becomes evidence perpendicular rows.

day later joints dry up and they need to be sealed with putty, or by using a rubber spatula or grouting.

jointing process

Application fugu need a certain device, for example, a container with a sealant gun or pastry sleeves to extrude the composition at the seams between the tiles.

avoid shortcomings putty coat must be thoroughly wiped with a damp cloth.Only need to be as careful not to erase the coating on the joints.

The best lining technique - a chess orientation, because it avoids more waste, scrap, orients the drawing.As a result, the picture turns out tender and clearly expressed.