How do I install PVC panels to the wall

selection of tools and materials to install the panels PVC

1. panels PVC
2. Metal profiles and corners
3. saw and hacksaw (as an option - jigsaw)
4. Brace gun and staples
5. planer and drill
6. Screws and dowels
7. Kleymery
8. Roulette and building level
9. Hammer

We provide installation of PVC panels.Step 1: Preparation of materials and surface

All materials should be purchased in advance, rather than mounting day because some of them recommended "lie down" in the room where they will be used for several days.If the delivery of the panel in contact with the frost, adapting the material time may be extended up to a week.

Note!The room itself, if it is not heated properly, you should warm up for a few days before facing the wall and keep it comfortable temperature.Sheathing should be carried out at a temperature of over 10 °.

before installing the battens on the walls, they must be leveled with plaster and primer.Otherwise, there is a problem when installing battens need to use pins that are very complicate rabotu.Shlifovat wall is not necessary.

Step 2: Mount batten

crate is made of metal profile, which is located at a distance from each other by 30 cm Attach to be so that the latter had a lower profile in the 10-30 cm from the floor, and the upper corner concerned.ceiling plinth.Reiki battens (guides) must be fixed after alignment and generate markup wall level of 50-60 cm from each other.

Note!In rooms with high humidity is best to use galvanized profiles.

If the alignment of the walls have not been made in advance, to avoid distortions and distortions on the rail in the places where the walls have chipped and uneven, you can attach small pieces of wood.For mounting the profile needed screws and screws.

First take the profile and attach to the wall, measure the level of the point of attachment.In these places, make the holes in the place that anchors, and then profile, and tighten the screws.

Step 3: Mount the first panel

If the sheets are mounted vertically, the length of the sheet is the height of the room, if the horizontal - the width of the walls.Measure out the required length using a tape measure and mark on the sheet lying on a level floor.Cut material is most convenient hacksaw or jigsaw.

In order to proceed to the skin, you will need a perforated metal corner that is placed on the first panel and attach it to the wall.Then comb the panel is placed in a corner.Make sure that as part of the flat panel area, to avoid distortions.

Next you need kleymery (metal brackets that hold them specifically invented for panels).At its basis have sharp barbs which are placed in the profile, and on board panel, thereby providing excellent fixation to the next sheet.

Step 4: placing the following in a groove panels

Then mount panels are at an angle.It is important that there were no gaps between the sheets.To prevent damage, you can take a piece of wood and put to the panel over the entire length, then by clicking on the comb, place it in the groove of the first panel.Push on the comb should be both accurate and strong so that the sheet was fixed in the groove.The panels are fixed to the profile kleymerom.

Step 5: installing the last panel

To install the last panel, as well as to the first used area "P".It is placed in the corner between the wall and attach the sheet to the first corner, and then to the previous panel.The walls are covered!

The video shows how to mount panels PVC wall to work had excellent results.

Step 6: decoration panel finishes

At the heart of the decor of the walls is, first of all, registration of the top panel, which can be carried out corners and eaves.In addition, the special importance and complexity of the installation has electrical outlets, which can be either close or bring wires elsewhere.For example, you close one of the existing outlets, while the second to put the double, or move the socket in a more convenient location.This will reduce the space consumed and simplify the work as a whole.Preparation of outlet you must perform before plating to could only be attached directly to the box and the lid.With regard affixed panel, cut a hole in it to the point of a jigsaw power, and then mount as usual.After the socket mount directly to the panel.

Before starting work, check some educational videos on the subject.Perhaps you useful tips as shown in the trailers.

Remember that PVC siding panel - is not only a functional and user-friendly in terms of cleaning, but also beautiful, allowing the room to always have a smart appearance.Good luck in your repair!