How to embed the castle interior doors

What you should pay attention to the hole for the lock

Before you start working on the sidebar of the castle in the interior doors, it is necessary to take into account some factors that may affect the quality of work:

• door lumber thickness should not be less than 40mm, or in the sidebar of the castle just will not make any sense.
• Particular care is manifest in the process of measurement and select the drill.wrong size hole may damage the door once and for all.
• also need to devote particular attention to road marking.This process is the key to a successful outcome.

crashed castle interior doors with a drill and chisel: step by step instructions

Prepare in advance the tools that will be required in the process:

• Pencils
• Drill
• Drills
• Hammer
• Screwdriver
• Rounded file

Step 1. Application markup on interior doors

is first necessary to draw a horizontal mark on the door, in the place where the castle is located.As a rule, the distance from the floor to the mark of one meter (plus or minus 10 cm).

Note!You can place a locking mechanism, and based on the individual performance of man.To do this, could move his hand in the door the place where it will be most convenient accommodation likely a lock mechanism.Then apply the appropriate markup.

Then you can start the markup for a frame lock.First, to have carried out the horizontal line you need to make the body of the locking mechanism on the end of the door and circle it.Next to the site of the alleged placing of the handle must be pressed down with a pen and circle, too.After it should be noted the estimated location of the keyhole on the front of the door.

Step 2. The process of drilling holes for keyhole

necessary to pick up the drill so that the spindle could rotate easily traced in the hole.Then you need to fasten the drill markings and to make the through-hole.After drilling is to produce the same effect, only on the other side of the door - so the opening will be delivered finished and aesthetic appearance.

Step 3 drilling holes

lock body is necessary to measure the length of the housing of the locking mechanism.Then taken the bit of suitable diameter and it postponed the length of the lock case.Further, it should be noted on the drill depth slots with electrical tape.Drills on a prearranged line marking the body of the locking device.Then chisel removed all unnecessary parts.You can further polish the hole with sandpaper.

Step 4: Install the lock in the prepared slots

Next is inserted in the body of the locking device has done a hole and mark the location of the place of screws.Then it is necessary to fix with them a lock mechanism housing.The spindle is inserted through the lock body, handle pads are applied and secured with screws.

Step 5. Mounting the receiving pads on the door jamb

necessary to close the door in order to determine the location of a possible location of the lock tab.Then you need to trim threaded through a tab again to close the door and mark the location of the seat pad.Next, using the bit for the drill holes of the tongue, and on top of the holes with screws attached external pad.

Box Castle in interior doors with a router

Produce Box Castle in the interior doors can not only using drills and chisels.For these purposes often use such a device as a router.It is quite expensive to acquire, but it can be rented in the tool magazine.

With this device you can perform the following works:

• cutting holes for the locking device;
• alignment edges;
• training niches for hinges and locks.

Routers come in many types, but for the work that is described in this article is quite suitable immersion.

step instructions for lock the sidebar in interior doors with a router

Before you start to work on the castle of the sidebar in interior doors with a router, you need to prepare in advance all the tools:

• Pencils
• Drill
• hammer chisel
• screwdriver
• Elbow
• Fraser

Step 1. Securing leaf

door is secured with clamps.This process is done for the convenience at all stages of tapping lock.

Step 2. Marking leaf

Using square and a pencil on the door is applied markings, similar to the previous method.

Step 3. Cut recesses for a lock mechanism with a router

Next on the advance road marking made the process of deepening the slot for housing a locking mechanism with a router.Then it is necessary to clean the inner surface of the recess with sandpaper.

detailed visual description of the installation process, the door lock with a router on the interior doors can be found in the submitted video footage.

We considered two of the most simple and common method of installation of interior doors in the castle, and how to take advantage of them - a matter of habit and personal preferences of the master.