Operating the device in the toilet tank toilet repair case

How difficult device cistern toilet?

To find out what's inside the toilet tank, enough to remove its cap.In Soviet WC to release water from the reservoir had a pull chain or pull the lever or press.Drain in modern bathrooms is arranged very rationally.Almost never have to make an effort to roaring stream rushed into the bowl, washing away its contents into the siphon (which created a water seal to cut off odors from sewage) and further into the drain pipe.

In rare cases, the buttons are pressed is not very soft, but this is due to defect in the valve design.That's just about the fixture, that is filling the tank, we'll talk.toilet flushing tank device is quite simple.It consists of the drain valve, the valve-float on the water tap and, in fact, the very mechanism of draining connected to the trigger lever or push the suction action.

crane can be positioned both horizontally and vertically, in the latter case the tank filling is performed in silent mode, thanks to a special method of attachment of the float-valve

.From the outside to the tap joins a flexible hose whose other end is fixed on the cold water pipe communication.

How to disassemble the toilet tank and assemble without unnecessary details?

Before get to work, make sure that the shut-off valve in the supply pipe is OK, and close it, and then empty the tank.Remove the gear lever knob located on the outside (modern systems often have, as such, button), we understand how to open the tank of the toilet.In Soviet toilets it just goes up, more recent designs can be shut-off locks, sometimes cover just leans back on its hinges.

Before disassemble the toilet tank, unscrew the hose from the tap, and the same procedures were carried out with the locking nut that holds the valve on the tank.The first part of the mechanism is removed.To remove the second device node in the Soviet design, we have no choice but to remove the toilet tank.The fact that these rather obsolete toilets consist of three parts: between the reservoir and the water closet with a ceramic pad, which is a separate piece.It is through it pass the bolts holding the tank itself, and the drain valve.

But first you need to disconnect itself pad attached toilet seat bolts.Unscrew them, remove the rubber cuff that connects the body with the outlet of the toilet area, and that the Soviet tank in our hands.Now unscrew the valve nut wiping screws, disconnect the site, which is also fixed with silicone to "guitar" - laying the appropriate form, which provides a seal drain holes.

If the tank rests on the metal bolts, it is likely that nuts are rusted on, in this case, try oil or acetic acid, and only in extreme cases the lower part of Spili bolts with nuts, but without damaging the toilet.

Modern cistern valve rests on the sealing ring provided with a thread and unscrew perfectly.No cuff and leading to the toilet, which saves you from too much of a weak link in the system, flush the entire system is mounted directly on a special pad water closet body, however, there is still laying there, in order to avoid leaks.

The seat of a tank, as it is screwed to the fixing nut passes through the gasket into the discharge funnel through which water under pressure is fed into the bowl.Install toilet tank is carried out without any adapters (except the Soviet concealed cistern and overhead), for high-quality installation gasket is necessary to thoroughly clean it and place under cover with silicone.

How to fix the toilet tank and put it in place?

Modern crane feeding mechanism understands quite easily understand the principle of detaching parts from each other, even without the scheme.Turn off the lock nut, which is in the middle of the site, and here we see the valve membrane, providing overlapping the water supply for the ascent of the float.If the tank continues to fill, even after float will be in the upper position, therefore, it is the cause of the valve, and most likely would be with a tear membrane.

change it and connect the crane to its original state.In rare cases, you have to change the entire water supply mechanism, how to remove it, as stated above.If water flows continuously into the toilet, so not operate the drain mechanism or cause of the discharge valve or in the gasket, providing reliable sealing tube ottochnoy necessary to prevent overflow tank .

Since there is a question about how to fix the toilet cistern, should be to start to clean the valve or, if necessary, replaced.If that fails, try a more tightly secure the siphon drain, as well as changing the gasket between the tank and water closet, as its defect could lead to flooding of toilets and below in the presence of neighbors - and their toilet at the same time.How to install a toilet tank back, we mentioned earlier.