We now know how to close the pipe in the bathroom from prying eyes

How to close the pipe in the toilet: methods and options

They depend on what materials will use a builder and decorator, also takes into account the location of the pipes in the room.

1. When all the water communications placed in the corner of the room, along the walls, they can close the ordinary decorative boxes.This method increases the functional area of ​​the room, and it is essential in tiny indoor toilets.
2. When pipes are located in the center of the wall, it is possible to install a false wall, which adorn and decorate.During the execution of a fake wall can be adapted to it a few shelves for storage of household items, and other chemicals.

Preparation

before determining to how close the pipe in the toilet, and the choice of shelter, make a analysis of the state of the pipes, due to the possible need of repair.

Important!Cast iron, sewer and metal water pipes have long service life, but often they are formed leaks.On this basis, it is necessary to pay much attention to the verification and inspection of pipes, so they had no trace of rust, which is indicative of a lack of integrity of the material.

If imperfections are found, you should immediately remove them.Material number 1 in their elimination are polypropylene and PVC pipe, setting that you can forget about all kinds of accidents, in fact, hide such communication is quite simple.

The next step in this work is the state of the surface of the walls.In order to hide the sewer and water drainage, you need to get rid of possible mold or mildew.It is understood that even the slightest portion damaged by mold, lead to a breach of the walls and threatening people's health.

detected problem areas cleaned of old coatings after treated twice with anti-fungal agents (primer) for the protection of the walls.And only after that you can hide the pipes under your chosen decorative design.

project

decorative designs most successful masking some time become plastic panel and gypsum board, as they are easy to install, are quite inexpensive and allows fully realize decorative ideas owners.

for organizing this pre-prepared design framework that can be made of wooden slats of various sizes.Also it is necessary not to forget about the galvanized profile, which is much stronger than for load-bearing structures and more stable humidity, deformation, etc.

Framework preparation falshsteny

1. On the wall at the side fasten profile (UD), which should have the correct angle ratio, since any misalignment will result in a loss of aesthetics.Krepjat profile nails 6x40 mm or 6h60 (anchor).
2. between profiles attach more jumpers, but the profile of CD.Their size is not less than 50 cm., And for plastic and plasterboard.
3. for shut-off valves and water meter must be installed doors.That cabinet was stable, at the bottom of the door set several profiles.

Framework preparation for the box

In order to install a box of drywall or plastic pipe in the toilet or bath is necessary to hold this list of actions:

1. The angular walls are fixed UD profile, then fromhis retreat 1.5-2 cm, to avoid damage from screws.
2. from the floor and from the ceiling segments stretch profile, which is placed according to a certain angle and ensures proper form box.
3. That wall that is angled, also mounted CD profile for stability.
4. As in the previous version, the elements are interconnected webs, size 50 cm. It is also worth taking into account the degree of location of the box, so that was not crooked located.
5. Outer frame finish

How to close the pipe in the bathroom when the only available PVC panel and plasterboard, and whether it is real?Experts say that nothing more is needed.

turns, optimal materials for the finishing of the cabinet walls are the PVC cover and washable GCR, a little less water-resistant plywood.

PVC panel is installed:

• It should use wide plastic strip, about 37 cm They allow you to close the box with one leaf..
• By the same principle used again profiled panel UD - to create designs on the walls and ceiling around the perimeter.
• necessary sizes are available and cut drywall sheets.During the slicing side of the bend, if necessary dorezat, you will need to use the inside of the bend.
• In the absence of interfacing strips, panels are attached to the starting profiles .. And if you still need to join, then use screws with a big hat and a jumper for a spin inside.

necessary to use self-tapping screws (25 mm) to mount high quality all the walls and plasterboard panels.If later a box was supposed to lay the tiles, the surface is primed panels.If you plan to paint the surface, it is necessary to all panels and cover poshtukaturit.

Following from the above, it becomes clear that the work with the panels concealing pipes bath, the toilet is not very professional, so it can handle each.So your patience and effort will be able to create the lowest score!