Gas boiler in a private home : how to replace

documents for installation of the boiler

hard to imagine, but the most common cause of failure of the installation of independent heating - it is a problem with documenting the new installation.

The first document, which you should use this guide SNIP 42-01-2002 "Gas distribution systems."All important specifications are installation of gas boilers in this document.In addition to the SNIP there is an article "Gas", which also establishes the procedure for the replacement of the gas appliance.This document fortunately or unfortunately no longer valid, but he did not prevent to be a source of useful information for installers.

Additional rules and regulations on gas appliances, heating, ventilation and air conditioning, a sound insulation and fire protection are given in the adjacent SNP.

device boiler

state allows you to install the heater in the basement only for single-family homes.Let us consider the look of the boiler circuit.

The photo shows the components of the boiler and how it works:

• monitoring device.
• Tyagopreryvatel.
• capacity for expansion.
• Heat Exchanger.
• burner.
• air valve (automatic).
• Heat exchanger for hot water supply system.
• Fuse.
• gas valve.
• fuse to prevent leakage of heating fluid.
• Contour fittings.
• coolant The drive element (circulation pump).
• valve for gas filling

To replace the boiler

1. Familiarity with technical specifications.Specifications prepared in the urban gas supply department after writing the corresponding application with the indication of the volume of gas consumption per hour in your home.City gas service grants permission and provides technical specifications.Official terms of registration - 1-2 weeks.And only after you will be given hands on application with a positive decision.It is understood that spontaneous installation of the boiler is illegal and dangerous, particularly if a complete change of heating communications plan to the house with a lot of apartments.
2. Design.Project installation of your gas appliance begins to be created after you get permission.In it you should paint scheme of the boiler installation, pipeline laying scheme communication scheme with the sector, a gas outlet, gas Posts layout with residential buildings.The project is developed especially design engineers who are licensed and provide relevant documents on the development of the project.



3. Gorgaza decision.Following the development of the project is sent to the organization Gorgaz to establish and agree on your site, the project must be approved.It can take anywhere from weeks to 4 months.

The package project documents served:

• Status and instructions for the boiler
• Sanitation Certificates on technical requirements.
• document confirming compliance with all standards of the boiler.

Important!These documents are prepared not you, but the manufacturer of boilers.

In case of refusal to Gorgaz you are required to call his reasons in writing, and provide ways to change the project.

And if the project is carried out in the "Pyaterochka", it shall be certified and in fact is a pass to the installation work.

Prohibitions and restrictions

gas boiler in a private home, although the wall, though you can not install floor:

1. on combustible surface.
2. In-line crossings,
3. The bathroom,
4. In the "communal" and hostels,
5. in unventilated areas,
6. The basement and the ground balconies, loggias,
7. on the ground floor, if the source - LPG.

Rules boiler installation in private house

domestic installation of gas boilers Standards are extremely simple, but are mandatory:

• more than 4 sq.m.area for installation;
• more than 0.8 wide entrance door;
• 0,3 m 10 m box in the cube to be a lot of light;.
• Over 2.5 m ceiling height;
• pipeline is mandatory;cold liquid.
• power unit and the cross section of the chimney must be equal.
• Wall coverings in the room must be neat.

Looking at this list, we can say that the most reliable solution would be to set the gas boiler in a private home in the kitchen, where there is also a stove.Why?Because the kitchen most similar in structure to the boiler because the installation of the boiler wall and will comply with the fire safety requirements and simplifies the connection of hot and cold water.The gas column while also can be easily hidden in a closet.If the floor is installed, it is necessary for the boiler room Hotel room for him.

How to install the device in a private house with his own hands?

Important!Anything associated with this kind of device is installed is strictly prohibited!Only the involvement of experienced professionals and only compliance!

Mandatory in the installers:

• Check the license for the installation of equipment.
• Temperature - 5-35 ° C, humidity up to 80%.

Arm SNP leadership, patience and go!