Bench to give their own hands

During summer work or autumn walk in the private garden, you want to have a comfortable bench seating.Produce your own it is easy, but you need to know the nuances of the assembly, the exact parameters of the required materials.For example, a bench to give his own hands and get a neat and really beautiful.

Materials

unusual and original looks the productof concrete slabs and wooden planks.But most importantly - a design may collect any host.To get started, you need the following materials:

• boards 15h3,8h200 5 cm;
• board 15h3,8h65 4 cm;
• board 15h3,8h17,5 2 cm;
• 12 concrete slabs 50h50h5 cm;
• threaded rod M16 (4 pcs.) Length of about 55 cm;
• M16 nuts + washers to secure the rods in construction (8 pcs.);
• wood glue to secure the rear backrest (optional but it is better to fix the screws);
• preservative for wood.

drawing

With this set of manufacturing garden bench made of wood will require a minimum investment of time and money.

Prepare for assembly boards and slabs is quite simple.It should be on every board length 2 m away from the top 7.5 cm from the edge of 10 and 40 cm (with one hand) and put down point.Repeat this procedure for the other side.Using a 18 mm drill bit for drilling wood to hold at these points.To understand how to make a bench with their hands properly, it is recommended to view the attached photos.

on each of 5 boards needs to be done on the 4-D holes at the points mentioned above.On plates must also measure out from the top 7.5 cm from the edge of 10 and 40 cm (both sides).Perform accurate boring of help special drill for concrete.Repeat surgery is necessary for all the plates.Each unit should be two holes of the bar.

detailed photos and drawings will enable the bench to give firsthand the simplicity of self-assembly of this garden forms.

Home build garden benches

Once training is complete, you need to put in order the wood and make it a beautiful appearance and durability.After all, summer residence bench, made with his own hands, and in dry weather, and will only be used outdoors during rain.

will need to cover the wood preservative, for example, Pinotex (usually buy boards have already been processed), then wait for drying material and to hold back the collection.It should be on one of the planks for seating (2 m) to measure on both sides by 50 cm - there will be boards edge.Next, the received marks measured from the center of 15 cm to the board - it will be part of the backrest.Stepping back for another 17.5 cm from the new marks, separate the pair of legs (both sides) and 15 cm for another couple of boards.As a result, the remaining period shall be equal to 5 cm (see. Figure).

at sites 15 cm is applied special glue for wood, which allows securely fasten the back and bottom.K 2-meter board glued boards 65 cm in length, perpendicular to the seating board.In addition, they are fixed with screws yet.

further formed between the protrusions, as shown in the photo, pasting pieces made with parameters 17,5X15 cm. All the glued parts are clamped and held together until the adhesive dries.Time of hardening depends on the type of adhesive purchased.When the parts are securely fastened, performed antiseptic coating.

Additionally, you can cover all parts of the lacquer tree.

collection and consolidation of the central part of the structure

to wooden bench with backrest has been collected accurately and efficiently, it is recommended to start gathering on both sides.

take between harvested boards insert concrete slabs and thread the holes previously drilled through the threaded rod.For the convenience of fixing best to start drilling in both the left and right side.So, to achieve absolute evenness will be easy.

When all the parts are pulled up, you can proceed to the final stage - the tightening of the screws.Then the work will be completed and the original bench will brighten any area in front of the house or in the garden.

more video views for the manufacture of benches in the country with their own hands, you can make to this project their own ideas or change the settings for the convenience of the workpiece.

Video manufacturing benches with their hands