Build Daily

Building Materials

August 12, 2017 18:08

How to work with plasterboard with their hands

click fraud protection

How to start working with plasterboard

aforesaid material covering of walls is very similar to the assembly of furniture, however, the differences are still there.In particular, if the pieces of furniture can be assembled from parts produced using only one screw, it requires the use of special drywall profiles.Of course, you can priladit coating directly to the wall, but the slightest unevenness is clearly visible, and in the corners can turn discrepancy edges of the sheets.

Sawing plasterboard necessarily sufficient to note dividing line, do it on both edges of the slits to hold the line and a sharp knife construction, pushing it deep into the material.Now you need to flip on the overhanging part that the sheet was divided into two fragments without excessive dust.

That is why the work of plasterboard begins with marking the location of components and installation at the appropriate places fasteners frame.With the help of plumb and level determine all the irregularities of the walls and exhibit support section attachment so that all elements of the framework were at the same level.

If you plan to decorate the ceiling and, starting from him, then plasterboard wall will provide additional support for the ceiling design.You need to be clear that you get.Better to spend a few days on the design than to prevent an incorrect cutting sheet.

Slopes of plasterboard - worthy setting for

Many windows faced the finish slopes and are well aware that a perfect result with the help of plaster to get extremely complicated, it requires a great experience, which is usually always a little bit, but not enough.So it makes sense to go the easiest way, especially since it is almost the same as the wall cladding with plasterboard.

Take waterproof gypsum board, measure and cut the necessary pieces to put off for the time being to the side.Slope and purify gruntuem.By the edge of the window frame to fasten the starting strip of plastic lining in the future, we will insert it face plaster strips.As fasteners for U-shaped strips can be used for metal screws.

Now there are very few to complete the work.Prepare adhesive plaster and cover them generously primed slopes, and then paste the item into the prepared p-shaped bar, having admitted to silicone.Band presses against the wall on the opposite side Do the same operation.

fasten not only the frame but also to the side slopes on the same level as the upper band eventually moves into place smoothly it is designed as furniture on the top of the sled in the starting strip window.Around the window opening slopes of plasterboard can be finished to your liking, for example, special plastic corners.

What and how to fasten drywall?

Actually, slightly above mentioned about how to fix the drywall on the walls and ceiling, but without any details.Now is the time to expand a little this interesting topic.Being sure of the evenness of the walls of your apartment, you can perform the installation finishes without a skeleton.In this case, you have two options - nails or screws.

If the brick walls and wooden, the first way easier mounting, drywall nails perfectly punched and reliably stuck to these surfaces, without leaving out.To work, use a special hammer, which you do not break the fragile cover sheets.

If you are lucky enough to own screwdriver or electric screwdriver, which, in fact, the same thing expressed in different form factors, use mounting screws, tighten them hand impractical, too much effort. selecting for fixing profiles, make sure that acquired the right sets, two of them: Guiding sections for ceiling profiles and rack rails .

confining wall, immediately perform around the perimeter of the floor line parallel to the walls.The indentation will consist of the thickness of the drywall and profile, summed with the gap between the profile and the wall to correct irregularities and various communications.Too large, this indent should not do, otherwise the volume of the room significantly reduced.Ceiling same mark are made on the walls.

Mounting profile begins with these lines, followed by the consolidation of suspensions dowels, at intervals of not more than one and a half meters.Stand sections are installed vertically in the guide, ceiling stacked horizontally.Fixed ceiling and rack elements of the frame with screws to hangers and guides.Plasterboard

same way to mount the mounting frame, using departing from the edge panels 10 centimeters, and in the case of all the plates 15, so as not crumbled hem.Screws desirable to drown in the drywall, so as not to create roughness on which worked so hard to get rid.

instagram viewer