Construction cesspool of tires

To filter wells, latrines and drain holes, and a variety of septic tanks could last for as long as possible, or use a ready-made containers, plastic, or with the help of concrete rings strengthen the walls of the wells.Honey fact there is a very inexpensive and easy to implement way to create a sump using end-of-age of tires.However, be aware that such sewer service element to cope with only a couple of people.Another option, where such a cesspool in general can be considered the ideal solution - a septic tank at their summer cottage.And the careful performance of the tire pit is fully capable to cope with the responsibilities entrusted to it for years.

Selecting a location for the placement of the sump.

Since the construction sump does not provide a complete seal, the main way of disposing of waste mass will be their infiltration into the soil.When the surface of the walls and bottom of the pit silted up, for pumping waste will need to resort to assenizatorskaya machines.Meanwhile, when properly organized and efficient drainage is a problem will not arise often.

Choosing a place in the future cesspool, you need to consider its removal from water wells or wells.Best of all, that this distance does not become less than 25 meters.In addition, if the house has a deep foundation, this factor should also be taken into account, ie. A. The distance between the hole and thus the foundation should not be less than 5 meters.The diameter of the well at the same time will depend on the size of the used tires.

Earthwork

dig a pit diameter and depth suitable for arranging such a cesspool, and it is possible by hand, without the aid of expensive and not always available equipment.Of the tools in this version Works only need a couple of spades, both of which should be planted on the handle at least 2.5 meters long, it was convenient to work, when the well is deep enough.Bayonet shovel is suitable for loosening soil and convenient scoop to scoop and remove the earth from the excavation.

prepared the tools, you can begin excavation work, which are as follows:

1. - on the ground marked feature of shallow wells circuit, which is enough to put one of the tires, and cut around it in a circle some peg.During this operation, it is desirable to make the margin of 5 cm, which enables easy drop in of tires in the pit;
2. - just digging the pit.At this stage, a bayonet spade cut off the vertical walls and loose central part of the pit.The loosened soil is removed then Shovel.It is possible that with the deepening of the pit will fall into the meaning of it.In this case, it will be convenient to use shovels to as short as possible cuttings, but simultaneously need to monitor the state of the walls of the well, so they do not crumble inside.
3. - at least a few times during the entire cycle of digging is necessary to check the diameter of the resulting pit.This is done by lowering the reference in a hole and fitting in place of one of the tires.

Laying prepared tire inside the sump

Before you start stacking tires directly on the bottom of the hole you need to fill schebenchatuyu cushion thickness somewhere 30 cm. This will safeguard against siltation bottom.The rim of each tire is lowered to the lower side, it is desirable to make an incision jigsaw, this will prevent the accumulation of waste in their masses.In the place where it will be placed upon sewer, it will also need to cut out the same jigsaw round hole of appropriate diameter.If jigsaw thus will not deal with a durable cord, you can use the manual with a hacksaw blade for working metal.

gidroizlyatsiyu particularly reliable for such a cesspool of the tire makes no sense to organize a large, but not more than wrap them with roofing material or a sufficiently thick strip of polyethylene.

of tires must be such that the most recent of them a few raised above ground level.This will prevent the overflow hole snow or rain water.All the gaps both between the tires, and between them and the walls are filled with fine gravel.

as cover for such wells will fit any suitable object made of wood or plastic.For example, you can use the waste cap for the wheel, which will provide excellent ventilation and facilitate the monitoring of the degree of filling of the cesspool.