What should be the thickness of the floorboard ?

thickness of the floorboard - an important factor that you need to look for when choosing a wooden floor.

This option would not only be mounted externally attractive and durable surface for the floor, but also to calculate the height of the door installation.

to choose the right thickness of the floorboard, you can not doubt the insulating properties of the floor.

Unlike applied laminate - a cheaper alternative wood flooring, parquet is more durable, and therefore durable.

Both of these materials are able to make significant changes to the interior space.

This laminate floors can be built in the premises regardless of their purpose, but of the floorboard - just for living rooms.

unites the two materials multilayer structure obtained in the production, but what's the difference between them - you can find out right now.

Compare laminate and parquet flooring

structure laminate isa four- or five-layer synthetic product.

If you analyze the laminate structure in detail and clearly, we can say that this is a kind of wallpapers, pasted on fiberboard plate and covered with a transparent resin material.

In turn, parquet product, despite the fact that strongly resembles a real piece parquet, and has a multilayer structure.

the production of it is going out of three layers of wood veneer, the first outer layer is usually made of valuable wood species (oak, birch, ash), and two lower - because of cheaper raw materials, such as pine trees or tree.

If we compare the appearance of laminate and parquet flooring, there is every material has its own individual characteristics.

View board similar to the texture of the tree, while find two with the same pattern parketiny impossible.

It's like, if I had to look for the two trees of the same form.

type of laminate can be very different.In the production of the product endow property to simulate any material that exists in nature - stone, marble or wood.Thus

segments laminate wood flooring for, unlike parquet material have identical patterns.

How to choose the thickness of the floor covering

are increasingly replaced by natural parquet floorboard.This is for several reasons, and chief among them are many no-cost and most likely, the simplicity and speed of laying.

Regarding the aesthetic characteristics of the said materials, they are apparently so similar that, if not the size, it was difficult to say what kind of product has been selected for the floor.

And now it's time to consider in more detail the existing dimensions of the parquet floor material.

Here you will learn about what options you need to choose hardwood flooring for a particular room.

Parquet board from 7 mm thick - is the most basic option is for this reason its surface can not be restored.

Recovery is subject only to the lacquer layer - the top coat.Most often, the product with the specified thickness mounted in hallways, children's rooms and corridors, with a minimum of mechanical action.

Parquet Floor, 10 mm thick - a product with the option 10, to mount only a qualitatively aligned basis.In the process of sanding is impossible to clean off more than 2 mm layer board.

Parquet board, thickness 12 mm - a floor covering like 10 mm.Furthermore, the product of 12 mm can be mounted on a "warm floors", manufactured using infrared elements.

board 15 mm thick - the most common coating.Installation of 15-millimeter products operate on the glue or using "locks".

When upgrading the surface of the board with the option of 15 mm, it is possible to remove the working layer up to 5 mm.Material with a parameter of 15 millimeters - the most suitable option for flooring in living conditions.

Board 20 mm - refers to a particular category of solid flooring.Most often 20-millimeter product is used for the floors in the offices and other civilian areas.

Video:

Parquet Floor 22 mm - the same as 20 mm material, a product with a thickness of 22 millimeters is used to mount the floor in public places.

Most often coated with this thick stack the deck by as equip it difficult patterns of long and expensive.

Typically, instructions for parquet floor with parameters 10, 12, 15, 20 or 22 mm indicated where to install and what technology to use when installing a particular type of board.

Here it is worth to note: at the operating board thickness of at least 6 mm in its upper layer may be subjected to grinding 10-12 times.

This fact corresponds to GOST standards so hardwood products with thickness of 20 and 22, as opposed to 10, 12 and 15 mm, can last for about 100 years.

substrate under the parquet material Forms

substrate is mounted under the surface finish, can be called a multifunction.

Its purpose is:

• in leveling the surface;
• in providing floor insulation;
• in lowering the noise produced in the process of mechanical action on the floor.

thickness of the substrate under the floorboard is an important criterion in the selection, as also on this parameter of the material life of the coating operation depends.

Typically, a standard substrate thickness is 2 mm.If we consider the substrate as the foam and cork, their use here would be inappropriate.

reason lies in the soft structure, which eventually causes deterioration of tool joints and the emergence of a squeak.

thickness of 4-8 mm cork backing, which can be found on store shelves does not apply under the floorboard and has another specific purpose.

Video:

Bitumen-cork backing - offers the convenience of laying, considered water resistant material, elastic and has the property to keep warm.

Tupleks - refers to a category of synthetic materials.The structure of the multilayer product, due to which the substrate is endowed with high levels of strength, flexibility and waterproofing.

any thickness suitable for the product, whether it be 7, 12 or 20 mm.

special attention on this list deserves plywood.Using

plywood as a substrate under the floorboard 7, 10, 20, 12 and 15 mm is appropriate to equalize small differences in elevation on a supporting concrete base, if necessary.

Features substrate mounting plywood

Application of plywood under the parquet flooring gives the opportunity not only to neutralize the irregularities bases, but also an opportunity to fix the basic quality flooring.

An additional advantage is the use of plywood and insulation to ensure strength and durability means operated floor.

Existing types of plywood, which are commonly used for parquet flooring:

• not moisture resistant;
• not ground;
• birch.

waterproof plywood should not be used as a substrate in the living room, because it contains the chemical structure of the components, unsafe for human health.

Moreover, plywood differences are the product thickness and width, with the thinnest of them 4 mm thick and - 21 mm.

For substrate selected plywood thickness that is less than ¾ thickness of the floorboard.

Before laying the plywood sheets on the concrete base, sawed them into four equal segments, which during installation will prevent the occurrence of pits and voids.

Video:

Plywood glued to the concrete base of a two-component adhesive composition that has the ability to dry quickly and firmly hold the material without the use of additional fasteners.

After the plywood substrate is mounted, it is necessary to process the surface grinding machine that will eliminate errors and level the surface.

And only then proceed to mount topcoat.