How to make a mirror with your hands

For women - an indispensable object mirror furniture interior.Convenient and useful table - table, equipped with a mirror, stands out in the interior, but at the same time should be in harmony with the overall style of furniture design.

not very difficult to make the dressing yourself.The classic dressing table with a mirror is a table with drawers and one or two tables.A good option - corner dressing table with triple mirror trellis.To start you with views mirror, a photo of which are laid out on the Internet and pick a suitable option.

Plans and necessary materials for the dressing table with mirror

Draw a pencil drawing of the exact mirror showing all sizes.The drawing will help you determine the required amount of materials and accessories for the manufacture of self-dressing.

1. table housing - tables made of laminated chipboard with a minimum thickness of 2 cm, the rear wall of cabinets and bottom drawers MDF.Mirror mounts it can be bought in the shop of furniture fittings, the same need to buy hinges for front doors, facades themselves for drawers, rails and bollards to them the door.Facades of MDF does not require additional treatment, just buy them suitable loop.
2. Pick identical pens and get the tape end.Feet can make yourself or buy ready-made.Crosscutting is flat and welded iron, and "U" - shaped, which is attached to the adhesive.And take the connecting hardware -. Screws, screws, SCREW, metal mounting brackets, etc. To buy countertops thicker plaque of chipboard, you can even ready for your size.

the cutting and assembly table with side tables for dressing

Apply markings on chipboard, thin pencil or marker.Straight lines saw better on the stationary circular machine with finely toothed cutting part.Curved lines run electric jigsaw.Very comfortable interior looks mirror angle.

1. When using an electric jigsaw pay attention to the correct trim.The plane of the web and the end edge should form a right angle.In the case of distortions and chips on a plane chipboard - will decorate the edge of the "U" - shaped end tape.
2. cut to size blanks are marked by the hole on the plane and the end face.For the markup you need a carpenter's area and awl.Chop in laminated surface point, move the marker.Spacing several identical holes in the end of the blanks, add them by using a stack of carpentry gon, draw a vertical line with a pencil and defining the center, put down a marker point.
3. For drilling you need a special drill for konfirmat or two ordinary wood with a diameter of 5 mm and 8 mm.The planes through a hole drilled 5 mm and 8 mm chamfered under the bonnet SCREW.Chamfer removed at least 2 mm deep.The mechanical part of the drill hole 5 mm to a depth of at least 4 cm. It is important to drill holes without deviations and distortions.
4. carcass dressing table in the bedroom, you will need a special "G" or "the Z" - shaped Allen key 4 mm nozzle or reverse screwdriver.To start Loosely individual parts, leaving a minimum clearance to correct blanks.Having the big picture, putting and modifying parts can be clamped tightly.
5. End Feed is of two types - flat or "U" - shaped.If the surface is trimmed neatly, without chips and imperfections, can be stuck flat trim.End PVC tape exposed the personal edge and welded well-heated iron.Excess edges are removed from the back of the sharp cutter assembly."U" - shaped lip hides chips and misalignment end edge, but it creates a ledge on chipboard plane, and in some places it may create some inconvenience.Such trimming can not be used in places of joining workpieces or it must be trimmed for tight junction planes.

Manufacturing and assembly drawer dressing table for

Decide guides.They need two, roller or sliding, you choose, the main thing - do not confuse the right with the left.The longer part of the guide is fixed with screws on the short side wall mirror and the second - in the drawer.

1. Three plates of equal thickness and height and facade MDF strip to be required to drawer dressing table.In the lower part, departing from 5 mm, a longitudinal groove is made, the thickness equal to the thickness of the bottom of fiberboard or plywood.It is going to SCREW drawer or wooden dowels.
2. When the thickness of the side wall of chipboard 20 mm, two blind holes for dowel no deeper than 15 mm.Standard wooden furniture dowels have sizes between 4 and 30 mm in diameter and 200 mm in length with a longitudinal grooved.Gather under construction dowel on the PVA glue.The bottom is fixed in the grooves, but the glue sets.

Attaching facades and mount the mirror on the dressing table

1. For fixing mirrors, there are two methods: mechanical fastening and double-sided tape for windows and mirrors.Along the perimeter of the mirror figure drilled holes for mounting on fixture diameter and sits on the PVA glue.In the second case, on the back side of the mirror there is a standard pad or glued to the sticky pads of a special double-sided tape for mirrors.
2. special blind holes for fastening furniture hinges are available for the front doors.For doors without landing slots they need to drill.The diameter of a furniture hinge mount 35 mm, on the need to put a stop drill, as a blind hole depth of 12.5 mm.The hinge sits in the slot, aligned and fixed short screws to the back of the facade and the interior of the side wall of the dressing table.On the loop are two adjusting screws by means of which the correction is made on the facade planes.

final touch - mounting handles on the facades of cabinets and drawers.For this purpose holes are drilled along the diameter of the fixing screw.Be sure to put the inside of the metal or plastic washers.Beautiful stylish pens always catch the eye and can drastically change the very homely furniture.