Bar stool with his hands

bar counter in the house will finally finished look after the equipment of its respective chairs.When choosing bar stools for the kitchen should take into account their compliance with the style and design of the existing bar.The proposed bar stools, a photo, which can be found on the Internet, does not always correspond to the designer's plan.Having a general idea of ​​joinery, a small set of tools and creativity, you can make your own wooden bar stools for the home.

Toolsand materials for the wood bar stool

All materials for the manufacture of bar stool made of wood can be bought at the nearest hardware store.Some design elements that you could not make at home, you can order in a carpentry workshop.To determine the size of the comfortable bar stools measured the distance from the floor to the bottom of the countertop bar.The gap between the top and the seat of the chair should be 30 - 35 cm

1. For electrical tools needed:. Drill with drill bits with a diameter of 3 and 6 mm, jig saw, screwdriver.
2. hammer, planer, chisel, measuring tape, carpenter's area.
3. Sandpaper, self tapping screws (5x20, 5h30 and 5h80).
4. Bruce - 50x50 array and shield (side-bar) with a thickness of 25 - 30 mm of pine, beech or birch.The approximate diameter of the array seat bar stool - 360 mm.
5. Stain, varnish, thinner and brush.

Before starting work, make working drawings bar stool with exact dimensions.This will help to determine the required amount of consumables and during joinery.

process of making wood chair for bar

Guided drawings for the manufacture of bar stool with his hands, put a pencil or marker marks on the wood piece.

1. Using an electric jigsaw, Solid wood carved circle 360 ​​mm in diameter, which will serve as the top surface of the bar stool.The surface is processed by a grinding machine, and on the edge of the chamfered.The circle of smaller diameter, about 260 mm, cut out for mounting and fastening the legs of the chair.
2. seat can make the square of the same general side-bar or splice of two - three boards in widths from 120 mm.For splices in the longitudinal end side of a router eat through tongue and a groove.Glued blanks are joined and fixed clamps are kept to dry completely.When sizing using carpenter's glue or PVA furniture.
3. The legs are made of timber section 50x50 mm.Electric a plane blank prostrugivayutsya along the entire length with a small cut.Thus, the cross section was 2.5h2.5 cm at the bottom of the legs and the upper part, fastened to the seat, it is possible as a column.
4. for bar stool take four progam.They further strengthen the construction of the chair and serve as a support bar for the legs.Beam section 2.5h2.5 see prostrugivaetsya and end parts zapilivaetsya spike.The legs at a height of about 25 - 30 cm from the floor jack under the hollowed spike.Pronozhkami inserted into the socket on the glue and fixed twine.

Building wooden bar stool

Details bar stool gather tightly without gaps and clearances.After fitting parts or halves connected by a pair of stools dry, then glue.Sharp corners slightly rounded spines.

1. In the working of the mounting surface for mounting feet drilled two holes on each foot dowel diameter 6 - 8 mm.Mounting the shield should be worn on the boring machine is very tight.In addition, the legs are strengthened with special metal corners on the screws.
2. top of the mounting board mounted facade seat.It can be mounted with screws on the rear side panel.Bar stool is placed on a flat surface, and the legs are fitted.In order to prevent the wood shear, at the ends of the legs are chamfered.
3. carefully polished, wooden chair for the bar is covered with stain and varnish.For a more aesthetic appearance varnishing is done in two - three layers.After the first and second opening, the surface is treated with fine sandpaper.After the third - a felt polishing pad.

soft seat and back chair for bar

sometimes on the basis of the chair frame for the bar are mounted small of the back, and even the armrests.The seat is soft or semi-soft.The filler used furniture foam or batting.Since the bar stools will be used in places of meals, pay attention to the quality and practicality of the upholstery.Good leather, leather, Barkan or other upholstery fabric.

1. According seat perimeter and with its rear side with a thin layer of glue.Use glue BF- 88 or PVA furniture.Glue is applied to the foam edge pads and upholstery edge pattern.
2. Having given a few minutes to thicken the glue, lining tightly pressed against the seat and tightly fitted by the upholstery fabric.On the inside of the corners first and then around the perimeter trim is fixed furniture stapler.Fastened seat in the last instance, after varnishing.
3. semicircular support members and the intermediate balusters for the backrest can be ordered in a carpentry workshop.For their manufacture will require turning and milling machines.Details are attached to the glue and dowels.