Build Daily

Equipment

August 12, 2017 18:06

Errors washing machine Daewoo: error codes le, e8, h6 and malfunction of machines Daewoo

click fraud protection
Errors washing machines Daewoo
  • Error Codes
  • Frequent faults
  • Tips and prevention of damage

Although the technique of Daewoo is not the most popular on the market, washing machines of this manufacturer are on sale and are often purchased by our compatriots.Such devices are extremely reliable, but broken as cars from other brands.Thanks to the self-diagnosis system the user can understand that the device is defective and find out what to do.

Error Codes

code

What does

Causes of errors

What

LE

problem with door

door is closed tightly enough.

necessary to open the door, and then close it tightly enough.

faulty lock on the door.

Check the lock operation and if the item is faulty, do its repair.

OE

problem with the water draining

Improperly installed or drain hose is blocked, (kinked or clogged).

Check that water flows through the drain system.Conduct an audit of the filter and drain hose.

Broken drain pump.

Check pump operation, including its chain.

UE

imbalance problem

linen inside the drum got off to one side.

Manually redistribute the load inside the tank, which appeared to eliminate the imbalance.

position of the washing machine are not adjusted.

Check the position of the device and adjust it if necessary.

IE

problem with the water supply

is no water or tap, through which water is supplied, is closed.

Check the valve and if it is closed, correct the problem.Also make sure that water is supplied to the apartment and its pressure is sufficient.

Water can not pass through the clogged drain filter.

Inspect strainer and its contamination, follow the steps for cleaning.

faulty solenoid valve.

Test the valve and check the condition of its electrical circuits.

At too low temperature was freezing the water intake hose.

Making sure that the reason is a low temperature, take measures to address this problem.

Broke pressure switch.

Rate pressure switch operation with subsequent replacement of the unit or repair it.

H6

problem with TAN

The heater electrical circuit is broken down.

Check chain PETN and efficiency of the heater.

E8

problem with loading sensor

No rotation of the drum due to the load sensor error.

Test the sensor and, if it is found failure, perform the replacement of the part.

E9

problem with the water supply

Faulty pressure switch.

Check the pressure switch itself and the tube, paying also attention to the connecting circuits.When detecting a fault, replace the pressure switch operating unit.

Frequent faults

Most often the masters of repair washing machines Daewoo owners of technology are turning for the following reasons:

  • failure of the control unit.This can manifest different failures during the wash, for example, increasing the length of the apparatus, stop during washing.
  • Breaks water level sensor.
  • clog up the filter in the priming path.
  • failure of the sensor.The water is heated and often bad machine stops operating during washing.
  • wear out the drive belt.
  • failure of the heater.Most often, this failure is associated with the formation of PETN on scale or rust.
  • cuff begins to flow tank.

Tips and prevention of damage

  • Before performing cleaning washing machine Daewoo, it is important to disconnect the machine from the network.
  • While the machine is working, it should not be exposed to water spray in order to prevent short circuits.
  • Before each washing check whether an empty tank for detergent and time to remove the remains of powder or chronic conditioner.If the container is present in the wash water, its drain before the next washing before falling asleep in machine detergents.
  • for container cleaning detergent to turn it counterclockwise and pull the bit.Rinse under running water container, it is returned in place.
  • If the drum came and stayed for a while in easily rusting objects, rust may appear on the tank.To remove it, use special features, but the drum cleaning can not be used metal tools or sponges.
  • top of the washing machine should be cleaned with a damp cloth, using only valid detergent (non-abrasive and solvent-free or benzene).
  • Regularly check the water inlet filter to ensure that its mesh is not clogged.

many interests wall models of washing machines Daewoo.The process of washing, you can see in the video Vasily Tolkachev.

To prevent malfunctions worth doing a few simple steps that make your life easier and increase the lifetime of the washing machine.More about them is told in the Ukrainian program "All bude good."

instagram viewer