Decorative well with their hands

Cottage has long been not only a holiday destination, but also an occasion to realize their creative potential.Everyone strives so design your site to, and at the very heart rejoiced and to impress the neighbors.Often the design is carried out in accordance with the rustic style.In this case, a decorative well, made with his own hands, is very appropriate.Below are step by step recommendations, pictures and drawings to help in the work.

drawing

The scheme below shows all the components of future construction.

Externally, this design looks natural.But this is a decorative element of landscape design.To arrange your yard so well, you do not need to dig a hole.It is enough to put in a little effort and build a decorative well in the country with their own hands.

Creating tip

headroom - is the foundation of a decorative well.

to plank tight to each other, at the ends of every detail make indentations (grooves), which will play the role of a latch.You need to prepare the following tools:

• square (to measure out the right angle);
• fine saw (for slots);
• screwdriver;
• jigsaw;
• cutter;
• thin chisel.

double sided tape it is necessary to fix the saw blade of a small plate, which will perform the stop function and protect against accidental deep slits.When it is fixed, you can start cutting.

Next you need to put a chisel to the place where the end slots, and striking it with a plastic hammer.Since the chisel blade will cut a fragment of the board through the wood fibers, the desired part of the break off easily.

Next, it is necessary to chamfer, to get a nice edge.This will require a special cutter.Combining prepared plates via the turned-latch lock, collect a single structure.It should be noted that for the lower parts only need a notch on one side.

To make the top layer, as the second plank of each slot need only one hand.

To make the structure more rigid and reliable, it must be sealed, prisverliv to it using screws additional element.

To make the top of the need to prepare a board, cut them to the side of the angle.First, make the markup, and then cut a jigsaw that will go along the guide groove.

From prepared boards make the collar on the well head.

Figured columns

To you arrange the columns, which will be held on the roof, take the jigsaw.The tool during operation should be kept perpendicular.To perform the patterns you can use ready-made loops.

irregularities should be smooth with the nozzle on the drill grinding.

To be able to fix the roof, you need to make cut-outs in the form of part-time corner.First, make a mark, and then run a thin saw cuts.

Next, you need to drill holes in which to insert wooden Chopik.To openings not get too deep in the drill bit wear clip.

holes needed to securely connect the lateral support and the decorative columns.Keep in mind that the support bars should go strictly parallel.To do this, when you commit closely watching the allowances, they must be the same.

jumpers between the posts are fixed with Chopik.

By headroom bars are mounted on the inner side with bolts.

being built roof decorative well

to complete the work necessary to build the roof.

First, you need to make the rafters, to prepare all the details, and then engage in the assembly.Sharp corners connection details are contained in the drawings.

View notching the rafters side.

Make a support for the connection of rafters.This will require glue and screws.

to connect trusses and supports needed glue and screws.The rafters are mounted in pairs.For accuracy, it is necessary to fix the details of clamping belt.

To get the details attached 2 more pairs of trusses bolted from below.

to make linings for the rafters, it is recommended to use the sander.

pads are attached to the rafters on both sides with adhesive.

Here you can see a way to connect to the carrier plate.

On the roof rails mark the corner and cut fragment of a jigsaw.

Roofing trims need to be sanded.

1st row roofing strips are drilled first, then attach the screws to the rafters.

2nd row should be fixed so as to be hidden bolts holding the 1st row.

domes can be manufactured on a lathe.

So the roof will look decorative well.

Decorative bucket

first cut the crankshaft and a handle for lifting water.

to connect the parts used Chopik 8.5 mm in diameter.

elements to buckets were exactly the same, first of 3 boards made form for further work plane.(It is necessary to obtain an angle 6 °).

inserting a plate in the resulting recess, it is treated with a plane until the blade touches the side walls.

obtained blanks were combined and laid out in a row face up.The connection is fixed with tape.

Next, using the adhesive system and the V-shaped grooves and spikes combine parts and tightening the straps to fix.

resulting cylinder is put on a piece of plywood and encircle the internal circuit.It will turn the bottom.He cut out a jigsaw.

bottom of the need to drill.These holes are needed for drainage.Also, the side in the bottom of the boards in places of connection holes are made and inserted Chopik.

From the outside bucket tin reinforced tape.

Instead, you can use the handle fragment of twisted rope.It also takes for imitation of a rope.

If something is not clear how to make a decorative well made of wood, you can watch the video.It's pretty hard work, which will take about 10 days.But try you will not be in vain.As a result, the garden will get the original decoration.

Video create a decorative well with their hands