Metal fence with his hands

Metal fences are reliable, durable, beautiful, relatively inexpensive and simple in arrangement.With the assembly of most of the existing kinds of fences made of metal can cope on their own, even without the experience of such events.

Study the following guide you will learn how to do just 4 different iron fence.Choose the most vending modification of the fence and start to work.

Mount the frame and supports

order of arrangement of struts and cross members remains the same for all the fences, in addition to the mesh fence.

set to work.

1. shovel or auger.
2. Roulette.
3. rods and rope for marking.
4. level.
5. gravel.
6. Sand.
7. Cement.
8. welding machine.
9. supports.Suit metal pipes.You can use round or square tube (rectangular) cross-section.The diameter or cross-section of the pipe should not be less than 70 mm.
10. Laghi.To buy their manufacturing flat profile 40 mm wide and 25 mm thick.Laghi we fix horizontally.Thanks to them will be provided by rigid attachment profiled sheets.

first step

Learning plan area.Choose the most convenient place for the future arrangement of doors and gates - we leave them empty.

second step

Mark up the territory.To this end, the perimeter fence trying to drive rods and stretch the cord between them.At this stage, work placements note pedestals.The optimal spacing between these elements - 3 m.

third step

Roy pit for racks 200 mm in diameter and a depth of approximately 100-130 cm

fourth step

Install supports, carefully verifying their level..

fifth step

poured on the bottom of each pit 20-cm layer of gravel or gravel and fill with cement mortar.Give him 3 days to dry.Immediately we put on a cone-shaped caps on the support.They protect our fill of rain.

sixth step

Mount cross joists.For greater reliability of the fence do this by using the welding machine.The required number of cross members are selected according to the planned height of the fence.For example, for the protection of up to 180 cm is enough of two rungs.If the fence is higher, the number of lag increases accordingly.

Making a fence made of profiled sheet

What is needed.

1. Profiled.For fence arrangement best suited grades material C-8 and C-10 and C-20 and C-21.
2. Fasteners.Buy plugs 30-40 mm in length.
3. balloon car paint.

Mark	overall width of the sheet, mm	Useful width of the sheet, mm	Height mm	Metal Thickness
C-8	1200	1150	8	0,4-0,8
C-10	1155	1130	10	0,4-0,7
C-15	1200	1150	15	0,4-0,8
C-18	1150	1100	18	0,4-0,8
C-20	1150	1100	20	0,4-0,8
C-21	1051	1000	21	0,4-0,8
C-44	1047	1000	44	0,5-0,8
MP-18	1150	1100	18	0,4-0,8
MP-20	1150	1100	18	0,4-0,8
MP-35	1076	1035	35	0,5-1
H-60 ​​	902	845	60	0,5-1
H-75	800	750	75	0,7-1,2
H-114		646 600 114		0,7-1,2
NA-35	1100	1035	35	0,5-1
NA-44	1050	1000	20	0, 4-0,8

installation instructions

Supportsand the bar is already mounted.Then we do the following.

fix an overlapping profiled sheets in 1 wave.For fastening sheets using self-tapping screws.Clamps are screwed in increments of 500 mm.In the process of mounting the sheets will inevitably scratch.They can be quickly and easily hide the paint in the can.You can mask the usual paint and the color of the sheets, but it is more convenient from a container.

Video - Fence made of profiled sheet with his hands

Make a fence of metal picket

set to work.

1. Fence.To collect suitable product dimensions 25h80 mm.
   

   metal fence

   

   metal fence U-shaped 2 m

   

   Dimensions profiles metal picket

2. Support beams cross-section of 100x100 mm.
3. Clamps.

The toolkit is similar to the preceding instructions.

order of arrangement

Getting to mount picket.

Pre bottom and top of each shtaketiny (in places of attachment to the bars of the future) create 2 holes.The diameter of each of them should be a little smaller than the diameter of fasteners used.This is to ensure that the material is not cracked in the process of fixing.

We fix each bar to the cross with four screws.NEXT to shtaketiny were fixed at the same level and with the same length, unless otherwise planned design ideas.

Video - The fence of metal picket

Make a chain-link fence

Reliable and beautifulfence can be made of metal mesh welded to the polymer coating.

To install the supports is similar to the previous instructions.For the arrangement of struts using profiled stainless steel tube treated by zinc phosphate coating technology followed by coating with special polymer composition.

Recommended cross-section bearings - 6x4 cm, wall thickness - 1.5 mm.The height of the pick up in accordance with the selected panel height.

Section for fences are also being sold as a finished product.you can make them yourself if you wish.

used for the manufacture of sections of steel wire with a diameter of about 5 mm.Rods are placed perpendicular to each other and held together by welding at the intersection points.The result is a section in a grid with a mesh of square or rectangular shape.

to improve the appearance and performance properties of fencing wire covered with a special composition based on zinc, zinc in combination with PVC, in a complex with zinc and Nanoceramics polymer.

pillars installed, the section is also available.Getting mounting elements fence!

for fixing the panels to the supports using bolts, nuts and special brackets.Of the tools you will need a socket wrench.No additional materials and do not have to use the tools.At the end of the mounting holes are closed with special plugs.

installed optional accessories, for example, forged shaped elements if necessary.In order to provide additional protection on top of the fence can be mounted barbed wire.

Successful work!

Video - Metal fence with their hands