Connect the motor from an old washing machine

If the washing machine is broken, you should not throw it - possible connection of the engine from an old washing machine.

This part of the art will be able to serve for some time.

engine applications can be found very much.

Removing the engine from an old washing machine?

Washing machines work on engines that have a different design: the collector, asynchronous, electronic type.

Before you do anything out of the old engine, it must be removed.For different types of need to perform a set of actions.

for all types of engines in the first place, it is necessary to disconnect equipment from the voltage of 220 V, running water and sewerage network.

Video:

When disabled, the machine must stand for at least 10 hours.Capacitor during this time will have time to discharge.Only after this the engine can reach.Driving action is described in detail below.

Induction motor - wires that connect the part of the induction motor and the capacitor should not be cut off.The battery need to pull out the engine.

have battery may differ depending on the model of the washing machine.This can be a box made of metal, plastic, often encapsulated.

It is capacitor - one or more of which are connected in parallel with each other.

worth considering carefully how to connect e.motor and battery.

Wiring plan may differ.The winding may be connected directly to the network 220, and the other - through a capacitor.The existing scheme is to be changed.

It needs to be connected to a voltage of 220 V and start asynchronous motor rotation.

Should be careful - the engine components can be touched only after the capacitor is discharged.

collector - these low-voltage motors.Their stator mounted permanent magnets and is connected to a constant voltage.

The engine is usually a sticker on which specified the recommended voltage.Only such a power should be connected to this email.motor.

Video:

E - motor is necessary to get out of the washing machine together with a control unit.In block housing usually indicate the voltage to which you want to connect the motor.

It should be taken when a voltage is applied - it is important to observe the correct polarity, as reversed in such a motor is not possible.

happens that the engine does not start immediately.In this case, you need to find additional findings.They served a zero or a logical one.After that, start the engine rotation.

Mechanical - with the motor can be reducer, which drives the reversing device.It is possible to find two conclusions.

current, which is determined by the label on the motor is connected to the source.After that, the engine will start its rotation.Rotational speed of the e-mail.motor is low - only 4-5 revolutions per minute.

To connect the motor to the AC, you must perform the following steps:

• Available to be a special device, which define the winding wires - tester;
• To define a pair of wires, the probe of the tester is connected to any wire, and in turn checked by the others.If you connect the tester designated connection, these two wires, and there are a couple.Accordingly, the second two wires and make a pair;
• two windings must be measured at the level of resistance.Where figure more is the winding and is starting;
• from different wire windings to be connected in pairs, and then connected to a voltage of 220 V;
  recommended to set the switch to the wire winding starting.

There are times when you need to change the direction of rotation of the motor.In this case, the conclusions of the starting winding is recommended swap.

When connecting the motor to the voltage across the capacitor 220 or directly, you should be very careful.Before working on connecting the engine to fix.

it will not vibrate strongly in this position.Secure yourself and others is also very important.

second life of the engine of the old washing machine

Operating engine old collector type washing machine can be used by designing a variety of useful devices.Some of them are considered in this paper.

grinder

Sharpening machine - useful device in any economy.

He can make any man, if in possession of a work engine washing machine "Indesit", "Ariston" or whatever.

When attaching the grindstone to the engine may be a problem - the hole in the stone can vary from shaft diameter e.motor.

In this case, need more detail, which is specially machined.This adapter will be able to make any turner.To do this, he needs to know the diameter of the shaft.

Available must be not only an adapter.special bolts, nuts, washers must be present.

the thread on the nut must be cut, depending on which way the motor will rotate.

to rotate clockwise thread must be cut into the left-wing, anti-clockwise - right-handed.

If you do the opposite, that the stone will fly, since the work will go on unwinding.

If there is a nut with a thread, but it does not fit in their field, you can change the direction of rotation.To do this, you must swap the wire winding.

After connecting the operating winding to the network 220, the starter must be connected to a pair of working coil.

The other end should be briefly attach to the conclusion of the winding.The movement of the collector email.the motor will start at one side.

After changing the starting winding terminals places the motor direction will change to the opposite.

motor rotation can be changed without using a condenser.In this case, after the working coil is connected to a 220 V, stone sharply scroll to the desired direction.

engine will start and the machine will work.

Do not use e-mail.motors having a high capacity.For the grinding machine is enough engine that withstands voltage 150-200V.

emery stone must rotate at a frequency of no more than 3000 rpm.If the speed is higher, there is a risk that the grindstone burst.

Video:

If you use a machine at home, experts recommend the use of the engine at 1000 rpm.

Homemade grinder is necessary to provide additional elements that protect the working man behind it from dust, stone particles.

The housing can act as a piece of metal having a thickness of about 2 mm.

Vibrating

Applying motor of washing machine "Ariston", "Ardo" or another model, one can construct a vibrating table.

It is useful if there are plans to create a device tiles.It can be put in the courtyard of his house, garden paths.

Vibrating table - a simple construction.It consists of a flat plate, which is fastened to the movable base compounds.brushed motor drives the movement plate.

Video:

As a result of the concrete in the forms out air quality improves tiles.

Regulation brushed motor should determine the scheme.If you set e-mail.the motor is not in place, the table will not be able to work properly, high-quality tiles will not work.

Mixer

Engine of old cars can be used to create concrete mixers.This product is not suitable for industrial volumes, but for the needs of their own yard is quite acceptable.

to turn the washing machine into the mixer, you will need not only the engine but also the tank.

The agitator type tank capacity to insert two blades in appearance similar to the letter "P", first removing it from the standard "native" promoter.

blades to build simple.It suffices to take a steel strip having a thickness of about 5 mm, cut from it the necessary amount to bend and two blades positioned so that they formed a right angle.

When the blades are ready, they must be connected to the tank through the hole where the activator was previously.

hole in the tank through which water drains must be closed.If everything was done correctly, you can begin to connect the motor.

Video:

Depending on how much concrete is planned kneading, the engine power is selected.If you need to knead a small amount, it is possible to install a single-phase motor.

If the volumes are larger, you should establish e-mail.motor on the washing machine more powerful.

Do not forget about the belt drive, which was in the machine.It is recommended to replace the gearbox.It will reduce the engine speed, while at the same time, momentum will be low.