septic Tapas

scheme sewage treatment in septic tanks Tapas

Purification processes that provide septic Tapas, are possible if the device anaerobic bacteria, the life cycle which allows to process and decontaminate organic, high concentrations contained in household waste water.

Cleaning in the construction of this type is as follows: in the first stage the contaminated water gets into a special chamber where the coarser impurities are removed, and then transported by airlift drains into the tank, aeration tank, in which the next step.

This process is the most important part of the treatment, as it is here added to the drains of the microorganisms that carry out processing of organic matter and its transformation into the mud, which, together with the remaining contaminants in the water settles in the third part of the plant - a pyramidal sump.The purified water should be the next part of the septic tank, after which it can be withdrawn.

accumulate in the settling tank sludge is necessary from time to time be removed from the buildings, that is very simple and requires no special skills.Also it can be used as fertilizer for crops and plants.

Device features

1. cleaning effect is 99 percent
2. design is small in size
3. consumption is relatively small
4. Operation is simple, the cleaning process is performed automatically
5. At work does not appear noise and odor
6. Easy installation
7. Variety of models in accordance with the amount of waste

mounting devices for

site Tapas install a septic tank should be at a distance more than 5 meters from the foundation structures.Next should begin excavation - pit is constructed according to the device model.For example, Topas 5 m 1,0h1,2h1,4 sizes must be prepared pit, which measures 1,8h1,8h2,4 m. And make it formwork.

Then the bottom of the pit poured a layer of sand 15 cm thick. The level of the septic tank hatch rises above the ground, which will simplify the operation of the device in the spring and will protect it from the damage occurrence.If you do not, at the time, when the snow begins to melt, the installation may flood, causing damage to the compressor, and often the entire system.

Choosing model septic tank, mark the placement of groundwater is required to take into account.In situ aquifer close to the surface, you need to choose the model that mark contains the letters PR.In these effluents discharged through the pump, which is part of the structure.

Next, you need to connect the device to the sewer system section, which uses polyethylene pipes with a diameter of 110 mm.Pipelines are included in the septic tank at a distance of 0.7-0.8 m from the top edge of the structure (for models Long, this value is 1,2-1,4m).Slope sewage selected according to the diameter - 100 mm for the value of 2 cm per meter, for a diameter of 50 mm - 3 cm / m.

The next phase of work involves the sealing of the septic tank.This requires to make holes diameter 103-100 mm below the sewage pipes in the design of the outside.Sealing is carried out according to the instructions that came with your device.

Septic Tapas equipped with a cord made of polypropylene, which carries the nozzle attachment is placed in a hole by soldering.This will require the use of a hair dryer building, and a special nozzle.Connecting the water drain to the device occurs after mounting pipe.

Before sealing the device, you must check the correctness of the installation on the surface of the pit, which use the building level.

To start the installation work, you must provide a connection to its power source.To do this, use the cable 3x1.5 PVA, which fits into the corrugated pipe close to the sewage system.It should bring to the dedicated input on the body, and then the terminals are attached to it.After that, the other end of the cable is fed into the control panel and connects separate machine 6-16A.

The last part of the final work is balancing the pressure on the cabinet when backfilling the excavation ground.For this Topas septic tank filled with water and covered with earth recess in an equivalent amount, this operation is repeated until the adjustment is achieved with the installation surface.

maintenance and use

1. devices Shoe department, where the accumulated sludge is held every six months.You can seek the services of professionals, but also have the opportunity to pump out mass with a pump and use it as fertilizer.
2. cleaning filter devices and the replacement of membranes compressors made personally once in 2-3 years.
3. Aeration mechanism should be changed after 12 years of operation of the device, since his work is still allowed to enter into it coarse particles.If we ignore their disposal, can disrupt a septic tank.

Septic Tapas is a perfect technological solution for arrangement of sewerage in the area.It is simple to use, has good technical characteristics, as well as has a high efficiency of sewage treatment, which makes it completely environmentally safe use.