Finishing of plastic windows with their hands

Plastic windows today are unprecedented consumer demand.They are not expensive compared to wooden windows, durable and well-insulated room from outside noise, dust and wind.

But a correct installation of plastic windows is not enough, often the real problem for the population is the design of the window opening, ie finishing slopes of plastic windows.Many have resorted to the help of a professional plasterer, but such work is quite capable to fulfill their own hands without any special skills.

Types of finishing slopes

slopes - is the surface of the walls near the windows.In turn, they are internal, that is, indoors, and external - on the outside.Look carefully window slopes should not only in terms of aesthetics.This is a mandatory requirement for the conservation of heat in the room, finished slopes prevent fogging of windows and closed so foam will not saturate undoing moisture.

Slopes of plaster

most often plaster soffits.First, a primer layer is applied, after drying - several layers of plaster mixture (it may be purchased in any hardware store) as long as the slopes become completely smooth.When the plaster dries, it should be primed and painted.

Proper implementation of this procedure will take about a week, maybe more.The disadvantage of the slopes of the plaster is their fragility.Over the years, the plaster yellowing and cracking.

Slopes of plasterboard

The second most popular method of decoration of plastic windows inside a trim window openings plasterboard.It has good thermal insulation properties, it can also be warm.If you know the technology, then attach the slopes of plasterboard can be a few days, in contrast to the plaster slopes.

On a sheet of drywall using a jigsaw cut metered length and width, suitable for slopes from all sides - from the top and sides.The void between the wall and the sheet is filled with polyurethane foam, and the drywall is fastened by dowels.At the same time between the web of plasterboard and foam should be a bit of space.The upper slope is fixed in the same way.Three hours after hardening foam all joints and cracks smeared with a solution of putty.Metal corners attach to the protection of sections.

putty plasterboard surface is leveled and sanded after drying.Then it must be primed and painted.

Plasterboard durable, but to strengthen it in the room with high humidity can not be due to its instability to moisture.Otherwise, you need to purchase water-resistant drywall.

slopes of sandwich panels

Finishing of plastic windows of sandwich panels is quick and easy.Such panels are several layers of plastic between which the polyurethane insulation.These panels are easy to install with their hands, they do not require maintenance, well insulated and noise resistant to weather changes.Before mounting sandwich panels slopes measured parameters, which cut strips from the panels: side and one upper.

1. the Construction knife trimmed excess foam.Self-tapping screws on the edges of the window profile is mounted starter profile U-shaped.
2. topsheet sandwich panels inserted into the slots starting profile and fastened with screws.
3. On both sides of the window openings, to an existing profile, self-tapping screws are attached are 4 parts of the profile.They stacked sandwich panels.
4. At the edge of the window openings overlap on the sandwich panel is a F-shaped profile, forming a neat corners.
5. If turned uneven joints, they can be treated with liquid plastic.

worth noting the advantages of plastic windows finishes sandwich panels:

• resistant to sunlight, do not burn and do not turn yellow;
• panel design enables the finish slopes at any angle;
• have good sound insulation properties;
• retain heat and does not require any special care.

Slopes of cellular plastic

most easily perform finishing slopes cellular plastic or panelitom.It is glued to the surface of the slope.

For ease of use and covered a number of disadvantages of this type of slope.Firstly, it is important to use a more expensive and high-quality panel.Secondly, before applying strips of plastic need to further insulate the surface of the slope.If this is not done, the slope will freeze and form condensation.In addition, cellular plastics is limited by the width of not more than 25 cm.

Slopes Plastic Slopes

plastic mount pretty quickly.Externally, they are attractive, do not fade in the sun and just wash off the dirt.When installing plastic slopes used for mineral wool insulation.These slopes can fulfill unassisted.

finishing materials Windows

To trim plastic panels of the window you will need:

• plastic.Its length is 6 m, and a thickness of 8 mm;
• U-shaped strip of plastics;
• drill;
• construction scissors, a knife;
• insulation (mineral wool suit);
• level (building);
• wooden slats (about 1.5 cm thick);
• stapler for fastening plastic;
• screws;
• white silicone.

installing plastic slopes Rules

In order to properly secure the slopes of plastic is important to observe the following sequence:

1. When the windows have already been delivered, on the side walls along the slopes of a drill mounted plastic profiles with grooves, which will subsequently be exhausted plastic panels.
2. Using screws attached U-shaped plastic strip along the outer perimeter of the window.Thus, to get trough.
3. F-shaped strip is attached parallel to the gutter U-shaped band with a stapler.
4. Measured plastic strips are installed in grooves, and between the wall and the plastic laid wool.
5. At the end of the window trim plastic panels, white silicone can gloss over places where joints are a bit do not match.

When decorating plastic windows it is important to securely seal the mounting seams.It is known that prolonged contact with the external environment is the destruction of foam, it loses its insulating properties and eventually glazing can give a slope.Therefore, in any event, must be carefully insulated from the harmful effects of froth.Carefully produced finishing of plastic windows will give them comfort and aesthetic appearance.

Exterior finish of plastic windows

exterior finish window slopes can be done in the following ways:

1. most popular and inexpensive way to finish the outside of plastic windows is zashtukaturivanie.Due to its arsenal just a dry cement mixture, it is possible to quickly cope with the finishing work.And this does not necessary experience in construction.

To own plaster the outer slope of the plastic window, it is important to observe the following sequence:

• with a knife cut a good slope surface bulging construction foam and remove the dirt.Check evenness of slopes using level.You can start plastering the walls with a mixture based on cement and plaster with water;
• additional insulation slopes is not required, foam, and so is the heat insulator;
• layer of plaster mixture should cover the window frame and a half centimeters and completely cover the foam;
• wooden lath plaster layer is distributed.Angles overwritten.When the last layer is dry plaster - slopes can be painted.

1. Finishing plastic windows tape PSUL

PSUL abbreviation stands for self-expanding polyurethane sealing tape.This newfangled overseas invention is able to reliably protect the assembly seams from moisture, sunlight and frost.After completing a ribbon trim slopes, it expands to fill the space.

PSUL Among the shortcomings can be identified that this tape is not always possible to buy in the shops.

In addition, if the installation of glass to get a deep pothole, the tape does not help PSUL neatly decorate all the irregularities.Dyeing and processing surface of the belt is also not desirable.

1. Finishing slopes nashchelnikami

Furnish plastic windows with their hands easiest to perform with the use of so-called flat strips.This self-adhesive laminate or plastic strips that are remarkably hide all defects left after window installation.Flat strips come in different widths and colors.They are qualitatively close slopes and mounting seams against frost, moisture and temperature changes.What is important is the correct cut and fit to the size of the window flashings.Besides, it's an inexpensive building material.

Winterizing slopes

Typically, window slopes need insulation when the room itself was not sheathed heater is still in its construction.If there is an urgent need to insulate the window soffits inside, it can be done with their own hands, with the help of ordinary foam.

Stages insulation window slopes:

• blocks of foam, about five centimeters thick, it is necessary to cut the width of the building with a knife, which must be less than the width of the slope of one centimeter;
• on pre-plastered slope must be put foam sheets, using the mounting foam.The foam must cover the assembly seam;
• foam and fill the joints between the sheets of foam and profile;
• then insulation foam sheathe plasterboard.It can be plastered and painted.

Finishing of plastic windows.Video