Cupboard under the refrigerator with their own hands

order to free up additional space of the room, you can use the built-in appliances.Most places, perhaps, many took the refrigerator.Therefore, it is usually trying to build in furniture.This is especially true for small spaces in the "khrushchovkas".

most compact are the built-in refrigerators without freezer.They are often equipped with features noise and vibration suppression.Their capacity is usually from 90 to 170 liters.Such a refrigerator is possible without too much trouble to put under the countertop kitchen units.

Recessed model

refrigerators If a large family, you should give preference to large refrigerator.Such a refrigerator, perhaps today is the most common model.Such units are usually separate refrigerators and freezers.And, the freezer may be located both above and below.Many modern models are equipped with all sorts of features and additional capabilities.The interior surfaces are covered with antimicrobial coatings.

Another type of built-in appliances is a wine cooler.If the Western countries such refrigerators have already settle down for a long time, such a unit is purchased relatively rarely in our country.And if you buy it so, it would be a real boon.By name it is clear that it is specifically designed for wine storage.At the same time it supports the most favorable conditions for storage of any wine.

cabinet under the fridge to buy today, no problem.Therefore, increasing the popularity of receiving such a thing as optimizing kitchen space.Of course, it is possible to build in a conventional refrigerator, but in this case in your kitchen space will become even smaller.It added to the size of a refrigerator the size of the wooden hull.In addition, in order to open the fridge, you have to open at a time on two doors instead of one - door closet and refrigerator door.Therefore it is better still to be installed in a cabinet to use built-in models.Moreover, today it is possible to place a cabinet-fridge under the window, which will significantly increase the free area of ​​the kitchen facilities.

advantages of embedded units

1. recessed refrigerator models have several advantages over conventional.One is the capacity.Indeed, these models occupy less space, but they are quite roomy.
2. Many current models have zero camera that allows you to store food longer.
3. Furthermore, such a refrigerator can save on electricity.
4. As these units due to the decorative panel have less background noise.

cabinet under the built-in refrigerators model

Embed refrigerator may well be on their own.To do this, you need the following materials:

• furniture handles,
• awnings,
• laminated chipboard,
• tools.

When size measurements are made, it is necessary to make the furniture scheme.This will help to calculate the true size of partition walls and shelves.If the back wall you decide not to replace it, or bars, in order to increase the rigidity of the structure, it is necessary to strengthen a few jumpers.To a refrigerator in the closet because of the change in temperature and humidity is not broken, the top of the need to make a small mezzanine.It will help take excess moisture and thus increase the useful life of equipment.If it has, then we can start to work.Assembling of furniture is best done on the previously prepared pattern.

Embedded refrigerator does not have a decorative housing.This can be made with her own hands.You can easily make it in the color of your kitchen.In addition, there is such a system as a pantograph, with which you can connect the cabinet doors under the refrigerator and the refrigerator, and then do not have to every time to open two doors.

1. The box can be made for built-in appliances on their own, using laminated chipboard.This is done simply, even a novice.It is best to purchase these plates with color and pattern close to the kitchen headset.If the headset has complex elements of the cornice and decor, the plates are more expensive.But feeling sorry for them money is not worth it.
2. must be removed prior to the acquisition of the art measurements to determine the size of the future cabinet under the built-in refrigerator.When the plate purchased, you can begin to layout and cut parts for the future of the housing-cabinet technology.To cut these plates are best used jigsaw.Cut items must fasten together using screws furniture.
3. When making body for the refrigerator you must not forget to make the lower vent hole in the bottom.In addition, the cabinet should be to equip a small podium.The rear wall of the housing is not needed.To cupboard was exactly then when it is installed on the place you should use the building level.
4. When the box is ready and set in place, you can begin to install built-in refrigerator.Door cabinet under the built-in refrigerator should be issued by a pantograph system, ietwo doors together.It is important to properly adjust them so they opened silently.Sections slabs that remained open, it should be to disguise the paper edge.

When installing the built-in furniture should take into account some important nuances.Almost any model embeddable refrigerator has a personal system awning door.For some models, there is no system of hinges.

Today also found models of refrigerators with doors that are equipped with special hinges.In this case, the sliding doors open technique with respect to each other.When you install such a system it is necessary to properly distribute the weight of the door between the hinges.

Can I build a normal refrigerator?

Sometimes conventional refrigerator spoils the look of the kitchen, in which case it can be built into a cabinet.If the door of the refrigerator and the cabinet does not bind, they will be opened separately.In order to solve this problem, it is possible to construct a special niche for the technology, not hiding the facade.But in this case you need to own the refrigerator had an attractive appearance, and it is best if combined with your kitchen style.In any case, the best option are the models of refrigerators, which were originally designed for integration into furniture.Sometimes selling refrigerators and freezers are available individually, but they are still one set.One of them can be placed in a cabinet-fridge under the windowsill.

Before you embed a refrigerator in the closet, be sure the dimensions are measured with the help of his usual roulette.Thus it is necessary to measure the width, depth and height of the art.During installation, it is important to correctly position the radiator.In the new model it is usually below the radiator, and the old - on the rear side.It is important that the radiator does not come into contact with the body of the cabinet, because otherwise, all vibrations are transmitted furniture.Therefore, between the radiator and the inner surface of the cabinet should be a sufficient gap (2-3 cm).In addition, the intervals will facilitate installation and ventilation.The rear wall can never be installed.

as the material for the walls, you can use regular sheets of chipboard.If the material is purchased in a special shop, you may be asked to cut it to size in the store.In addition, the need to handle the door, fittings and fasteners.Before inserting the equipment front part of the refrigerator, you can paste over the same color as the cabinet.Finally, you will need a cabinet body, which will need to build and install in place.Doors should be installed when the equipment will already be placed in the cabinet under the fridge.Photos in this article show how it will look in the end.

Note:

1. When you try to build a conventional refrigerator in the closet will not be able to equip the bottom, and it will make the structure very fragile and flimsy.
2. In addition, case for such equipment would have a much greater depth to accommodate a refrigerator outdated sample.
3. This cabinet will very bulky and wide.After all, the conventional refrigerator itself has large dimensions.
4. also need to take into account the number of future doors.Since the need to open at least four doors.They should arrange so that each of them opened freely.
5. To improve ventilation of the enclosure under conventional refrigerator furniture should at present the rear wall, and this structure makes it worse.As a result, the cabinet turns flimsy, because of what may be unsteady.